Schmalz VacuMaster VM-BASIC Скачать руководство пользователя страница 41

Страница: 41 / 50

Maintenance

EN-US · 30.30.01.01610 · 00 · 01/20

41 / 50

9 Maintenance

9.1 Safety

9.1.1 Safety Instructions for Maintenance

The lifting device must be installed and maintained only by qualified specialist electricians and mechanics.

Personnel must have read and understood the operating instructions.

DANGER

Electric shock from touching live components

Serious injury or death!

Make sure that the electrical components are not live before installation, maintenance
and troubleshooting.

Switch off the mains switch and secure against unauthorized restart.

WARNING

Risk of injury due to vacuum!

Switch the vacuum generator off before performing troubleshooting or maintenance
work.

Make sure that there is no stored residual vacuum remaining in the vacuum circuit.

WARNING

Unexpected movements

Serious injury or death!

Before working on the lifting device VacuMaster, ensure that the crane cannot move.

WARNING

Risk of injury due to incorrect maintenance or troubleshooting

Check the proper functioning of the product, especially the safety features, after every
maintenance or troubleshooting operation.

9.1.2 Protective Equipment

The following protective equipment is required for installation, troubleshooting and maintenance
work:

•

Protective work shoes

•

Working gloves sturdy enough for the load

9.2 Regular Inspections

•

Observe the applicable country-specific regulations.

•

Comply with country-specific inspection dates.

•

Release the lifting device for operation only after approval by the relevant authority.

Содержание VacuMaster VM-BASIC



















































Результаты поиска

Содержание VacuMaster VM-BASIC

Отзывы:

Похожие инструкции для VacuMaster VM-BASIC

Бренды по названию

Популярные бренды

Schmalz VacuMaster VM-BASIC, Руководство по эксплуатации

Результаты поиска

Содержание VacuMaster VM-BASIC

Отзывы:

Похожие инструкции для VacuMaster VM-BASIC

Бренды по названию

Популярные бренды