Sanyo 85402843, Руководство по обслуживанию

Страница: 6 / 252

1 - 2
Mini ECO-i System
Address Settings
1
YE S
Make n ece ss ary correctio ns .
Check the alarm
co n te n t s .
Check the alarm co n te n t s .
T u r n OFF the i n door a n d
o u tdoor un it power.
NO
*2
* 3 * 3
*2
CA S E 1
CA S E 2
CA S E 3 B CA S E 3 A
YE S
YE S
NO
YE S
NO
NO
NO
YE S
YE S
NO
Recheck the item s to check before the te s t r un .
Are the i n ter- un it co n trol wire s
co nn ected to more tha n 1 refri g era n t
s y s tem?
I s it po ss ible to t u r n ON the power o n ly
for the 1 refri g era n t s y s tem where the
te s t r un will be performed?
Will a u tomatic addre ss s etti ng be
performed i n Heati ng mode?
I s it OK to s tart the compre ss or s ?
T u r n ON the i n door a n d
o u tdoor un it power.
S hort-circ u it the mode cha ng e pi n
(CN50) o n the o u tdoor mai n un it PCB.
At the s ame time, s hort-circ u it the
a u tomatic addre ss pi n (CN51) for 1
s eco n d or lo ng er, the n relea s e it.
S hort-circ u it the a u tomatic addre ss
pi n (CN51) o n the o u tdoor mai n
un it PCB for 1 s eco n d or lo ng er,
the n relea s e it.
S hort-circ u it the a u tomatic addre ss pi n (CN51) o n
the o u tdoor mai n un it PCB for 1 s eco n d or lo ng er,
the n relea s e it.
S tart i n door a n d o u tdoor un it
cooli ng operatio n .
LED 1 a n d 2 bli n k alter n ately.
S tart i n door a n d o u tdoor un it
heati ng operatio n .
LED 1 a n d 2 bli n k alter n ately.
LED 1 a n d 2 bli n k alter n ately
(abo u t 2 or 3 mi nu te s ).
I s it OK to s tart the compre ss or s ?
T u r n ON the i n door a n d
o u tdoor un it power.
T u r n OFF the i n door
a n d o u tdoor un it power.
T u r n ON the i n door a n d
o u tdoor un it power for that
refri g era n t s y s tem o n ly.
Are LED s 1 a n d 2 o n the
o u tdoor un it PCB OFF?
Are LED s 1 a n d 2 o n the
o u tdoor un it PCB OFF?
S et the No. of i n door un it s .
S et the s y s tem addre ss .
Whe n m u ltiple o u tdoor mai n un it s exi s t, di s co nn ect the termi n al s
exte n ded from the s horted pl ugs (CN 33 ) at all o u tdoor un it PCB s
except for 1.
Alter n atively, move the s ocket s to the OPEN s ide.
<O u tdoor un it co n trol PCB>
No. of I/U s etti ng s witch
( S 004 a n d S 005)
<O u tdoor un it co n trol PCB>
R.C. ADD s etti ng s witch
( S 002 a n d S 00 3 )
Refer to Fi g . 7-4
(Check the li n k wiri ng .)
Refer to “Table of
S elf-Dia gn o s tic F un ctio ns a n d
De s criptio n of Alarm Di s play s .”
*2 A mi n im u m of 5 ho u r s m us t have pa ss ed after the
power wa s t u r n ed ON to the o u tdoor un it.
* 3 All i n door un it s operate i n all refri g era n t s y s tem s
where the power i s ON.
Check that te s t r un preparatio n i s OK.
(Do n ot allow the s hort-circ u ited pi ns to remai n s hort-circ u ited.)
Refer to the remote
co n troller te s t-r un
s etti ngs .
S et the wired remote co n troller for te s t r un .
Doe s s y s tem operate?
Ret u r n remote co n trol to n ormal mode
Check a n d make correctio ns accordi ng to
“Table of S elf-Dia gn o s tic F un ctio ns .”
E n d te s t r un .
Make n ece ss ary
correctio ns
Test Run Procedure
G
Use caution when making the settings. If there
are duplicated system addresses setting at
R.C. ADD switch, or if the settings for the Nos.
of the indoor units are not consistent, an alarm
will occur and the system will not start.
G
These settings are not made on the indoor unit
PCB.
1. Test Run
06-408 Mini_ECOi_SM1 11/10/06 5:48 PM Page 2
获取更多资料
微信搜索蓝领星球