manualshive.com logo in svg

Samsung S3C2416, Руководство пользователя

Поделиться
Скачать
Samsung S3C2416 Скачать руководство пользователя страница 523

S3C2416X RISC MICROPROCESSOR  

LCD 

CONTROLLER 

  

 

21-3 

2 FUNCTIONAL 

DESCRIPTION 

2.1  BRIEF OF THE SUB-BLOCK 

The LCD controller consists of a VSFR, VDMA, VPRCS, VTIME, and video clock generator. The VSFR has 71 

programmable register sets and two-256x25 palette memory, which are used to configure the LCD controller. The 

VDMA is a dedicated LCD DMA, which it can transfer the video data in frame memory to VPRCS. By using this 

special DMA, the video data can be displayed on the screen without CPU intervention. The VPRCS receives the 

video data from VDMA and sends the video data through the data ports (RGB_VD, VEN_VD, or SYS_VD ) to the 

display device (LCD) after changing them into a suitable data format, for example 8-bit per pixel mode (8 BPP 

Mode) or 16-bit per pixel mode (16 BPP Mode). The VTIME consists of programmable logic to support the 

variable requirement of interface timing and rates commonly found in different LCD drivers. The VTIME block 

generates RGB_VSYNC, RGB_HSYNC, RGB_VCLK, RGB_VDEN, SYS_CS1, SYS_CS0, and so on. 

 

2.2 DATA FLOW 

FIFO is present in the VDMA. When FIFO is empty or partially empty, VDMA requests data fetching from the 

frame memory based on the burst memory transfer mode(Consecutive memory fetching of 4 / 8 / 16 words per 

one burst request without allowing the bus mastership to another bus master during the bus transfer). When bus 

arbitrator in the memory controller accepts this kind of transfer request, there will be 4 /8 /16 successive word data 

transfers from system memory to internal FIFO. The each size of FIFO is 32 words. The LCD controller has two 

FIFOs because it needs to support the overlay window mode. In case of one screen display mode, the only one 

FIFO should be used. The data through FIFO is fetched by VPRCS which has a blending, scheduling function for 

the final image data. VPRCS supports overlay function that enables to overlay any image up to 2 window images 

whose is smaller or same size can be blended with main window image with programmable alpha blending or 

color (chroma) key function. Fig. 21-2 shows the data flow from system bus to the output buffer. VDMA has two 

DMA channels. Alpha values written in SFR determine the level of blending. Data from Output buffer will be 

appearing to the Video Data Port. 

 

Содержание S3C2416

































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды