Samsung S3C2416 Скачать руководство пользователя страница 484

Страница: 484 / 672

HSMMC CONTROLLER

S3C2416X RISC MICROPROCESSOR

20-38

5.13 BLOCK GAP CONTROL REGISTER

This register contains the SD Command Argument.

Register

Address

R/W

Description

Reset Value

BLKGAP0

0X4AC0002A

R/W Block Gap Control Register (Channel 0)

0x0

BLKGAP1

0X4A80002A

R/W Block Gap Control Register (Channel 1)

0x0

Name

Bit

Description

Initial Value

[7:4]

Reserved

ENINTBGAP [3]

Interrupt At Block Gap

This bit is valid only in 4-bit mode of the SDIO card and selects a sample

point in the interrupt cycle. Setting to 1 enables interrupt detection at the

block gap for a multiple block transfer. Setting to 0 disables interrupt

detection during a multiple block transfer. If the SD card cannot signal

an interrupt during a multiple block transfer, this bit should be set to 0.

When the Host Driver detects an SD card insertion, it shall set this bit

according to the CCCR of the SDIO card. (RW)
1 = Enabled

0 = Disabled

ENRWAIT [2]

Read Wait Control

The read wait function is optional for SDIO cards. If the card supports

read wait, set this bit to enable use of the read wait protocol to stop read

data using the

DAT

[2] line. Otherwise the Host Controller has to stop the

SD Clock to hold read data, which restricts commands generation.

When the Host Driver detects an SD card insertion, it shall set this bit

according to the CCCR of the SDIO card. If the card does not support

read wait, this bit shall never be set to 1 otherwise

DAT

line conflict may

occur. If this bit is set to 0, Suspend/Resume cannot be supported. (RW)
1 = Enable Read Wait Control

0 = Disable Read Wait Control

CONTREQ [1]

Continue Request

This bit is used to restart a transaction which was stopped using the

Stop At Block Gap Request

. To cancel stop at the block gap, set

Stop

At Block Gap Request

to 0 and set this bit 1 to restart the transfer.

The Host Controller automatically clears this bit in either of the following

cases:
(1) In the case of a read transaction, the

DAT Line Active

changes from

0 to 1 as a read transaction restarts.
(2) In the case of a write transaction, the

Write Transfer Active

changes from 0 to 1 as the write transaction restarts.
Therefore it is not necessary for Host Driver to set this bit to 0. If

Stop At

Block Gap Request

is set to 1, any write to this bit is ignored. (RWAC)

1 = Restart

0 = Not affect

STOPBGAP [0]

Stop At Block Gap Request

Содержание S3C2416

































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание S3C2416

Отзывы:

Бренды по названию

Популярные бренды

Samsung S3C2416, Руководство пользователя

Результаты поиска

Содержание S3C2416

Отзывы:

Бренды по названию

Популярные бренды