manualshive.com logo in svg

Samsung S3C2416, Руководство пользователя

Поделиться
Скачать
Samsung S3C2416 Скачать руководство пользователя страница 478

HSMMC CONTROLLER  

 

S3C2416X RISC MICROPROCESSOR 

20-32  

 

Name 

Bit 

Description 

Initial Value

BUFWTRDY [10] 

Buffer Write Enable 

(ROC)

 

This status is used for non-DMA write transfers. The Host Controller 

can implement multiple buffers to transfer data efficiently. This read 

only flag indicates if space is available for write data. If this bit is 1, 

data can be written to the buffer. A change of this bit from 1 to 0 

occurs when all the block data is written to the buffer. A change of 

this bit from 0 to 1 occurs when top of block data can be written to 

the buffer and generates the 

Buffer Write Ready 

interrupt.  

1 = Write enable 

0 = Write disable 

 

0 

RDTRANACT [9] 

Read Transfer Active 

(ROC)

 

This status is used for detecting completion of a read transfer.  
This bit is set to 1 for either of the following conditions: 
(1) After the end bit of the read command.  
(2) When writing a 1 to 

Continue Request 

in the 

Block Gap Control 

register to restart a read transfer.  
This bit is cleared to 0 for either of the following conditions::  
(1) When the last data block as specified by block length is 

transferred to the System. 
(2) When all valid data blocks have been transferred to the System 

and no current block transfers are being sent as a result of the 

Stop 

At Block Gap Request 

being set to 1. 

A Transfer Complete 

interrupt is generated when this bit changes to 0.  
1 = Transferring data 

0 = No valid data 

 

0 

WTTRANACT [8] 

Write Transfer Active 

(ROC)

 

This status indicates a write transfer is active. If this bit is 0, it means 

no valid write data exists in the Host Controller.  
This bit is set in either of the following cases: 
(1) After the end bit of the write command. 
(2) When writing a 1 to 

Continue Request 

in the 

Block Gap Control 

register to restart a write transfer. 
This bit is cleared in either of the following cases: 
(1) After getting the CRC status of the last data block as specified by 

the transfer count (Single and Multiple) 
(2) After getting the CRC status of any block where data 

transmission is about to be stopped by a 

Stop At Block Gap 

Request

.  

During a write transaction, a 

Block Gap Event 

interrupt is 

generated when this bit is changed to 0, as result of the 

Stop At 

Block Gap Request 

being set. This status is useful for the Host 

Driver in determining when to issue commands during write busy. 
1 = Transferring data 

0 = No valid data 

 

0 

Содержание S3C2416

































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды