manualshive.com logo in svg

Samsung S3C2416, Руководство пользователя

Поделиться
Скачать
Samsung S3C2416 Скачать руководство пользователя страница 381

S3C2416X RISC MICROPROCESSOR

 

 

IIC-BUS INTERFACE 

 

17-1

 

17 

IIC-BUS INTERFACE  

1 OVERVIEW 

The S3C2416 RISC microprocessor can support one channels of multi-master IIC-bus serial interface. A 

dedicated serial data line (SDA) and a serial clock line (SCL) carry information between bus masters and 

peripheral devices which are connected to the IIC-bus. The SDA and SCL lines are bi-directional. 

In multi-master IIC-bus mode, multiple S3C2416 RISC microprocessors can receive or transmit serial data to or 

from slave devices. The master S3C2416 can initiate and terminate a data transfer over the IIC-bus. The IIC-bus 

in the S3C2416 uses Standard bus arbitration procedure. 

To control multi-master IIC-bus operations, values must be written to the following registers: 

•

  Multi-master IIC-bus control register, IICCON 

•

  Multi-master IIC-bus control/status register, IICSTAT 

•

  Multi-master IIC-bus Tx/Rx data shift register, IICDS 

•

  Multi-master IIC-bus address register, IICADD 

When the IIC-bus is free, the SDA and SCL lines should be both at High level. A High-to-Low transition of SDA 

can initiate a Start condition. A Low-to-High transition of SDA can initiate a Stop condition while SCL remains 

steady at High Level. 

The Start and Stop conditions can always be generated by the master devices. A 7-bit address value in the first 

data byte, which is put onto the bus after the Start condition has been initiated, can determine the slave device 

which the bus master device has selected. The 8th bit determines the direction of the transfer (read or write). 

Every data byte put onto the SDA line should be eight bits in total. The bytes can be unlimitedly sent or received 

during the bus transfer operation. Data is always sent from most-significant bit (MSB) first, and every byte should 

be immediately followed by acknowledge (ACK) bit. 

 

Содержание S3C2416

































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды