manualshive.com logo in svg

Samsung S3C2416, Руководство пользователя

Поделиться
Скачать
Samsung S3C2416 Скачать руководство пользователя страница 51

S3C2416X RISC MICROPROCESSOR 

 

 PRODUCT OVERVIEW 

 

1-23

 

4.1 SIGNAL 

DESCRIPTIONS 

Table 1-4. S3C2416X Signal Descriptions  

Signal 

In/Out 

Description  

Reset, Clock & Power

 

XTIpll 

AI 

Crystal input signals for internal osc circuit. 

When OM[0] = 0, XTIpll is used for MPLL CLK source and EPLL CLK 

source.  

If it isn't used, it has to be Low (0V) 

XTOpll

 

AO

 

Crystal output signals for internal osc circuit.  

When OM[0] = 0, XTIpll is used for MPLL CLK source and EPLL CLK 

source.   If it isn't used, it has to be float

 

NC AI 

Not 

connected. 

EPLLCAP

 

AI

 

Loop filter capacitor for Extra PLL

 

XTIrtc 

AI 

32.768 kHz crystal input for RTC. If it isn’t used, it has to be High 

(VDD_RTC=3.3V). 

XTOrtc

 

AO

 

32.768 kHz crystal output for RTC. If it isn’t used, it has to be float.

 

CLKOUT[1:0] 

O 

Clock output signal. The CLKSEL of MISCCR(GPIO register) register 

configures the clock output mode among the MPLL_CLK, EPLL CLK, 

ARMCLK, HCLK, PCLK. 

nRESET

 

ST

 

nRESET suspends any operation in progress and places S3C2416X into 

a known reset state. For a reset, nRESET must be held to L level for at 

least 4 OSCin after the processor power has been stabilized.

 

nRSTOUT 

O 

For external device reset control (nRSTOUT = nRESET & nWDTRST & 

SW_RESET)    *SW_RESET = nRSTCON of GPIO MISCCR 

PWREN

 

O

 

core power on-off control signal

 

nBATT_FLT 

I 

Probe for battery state (Does not wake up at Sleep mode in case of low 

battery state). If it isn’t used, it has to be High (3.3V). 

OM[4:0]

 

I

 

OM[4:0] set operating modes of S3C2416X  

Refer to “

S3C2416X Operation Mode Description Table

”

 

EXTCLK 

I 

External clock source.  

When OM[0] = 1, EXTCLK  is used for MPLL  and EPLL CLK source. 

If it isn't used, it has to be Low (0V). 

Memory Interface (ROM/SRAM/NAND)

 

RADDR[25:0] O 

RADDR[25:0] (Address Bus) outputs the memory address of the 

corresponding bank . 

RDATA[15:0]

 

IO

 

RDATA[15:0] (Data Bus) inputs data during memory read and outputs 

data during memory write. The bus width is programmable among 8/16-

bit.

 

nRCS[5:0] 

O 

nRCS[5:0] (Chip Select) are activated when the address of a memory is 

within the address region of each bank. The number of access cycles and 

the bank size can be programmed. 

nRWE

 

O

 

nRWE (Write Enable) indicates that the current bus cycle is a write cycle.

nROE 

O 

nOE (Output Enable) indicates that the current bus cycle is a read cycle. 

Содержание S3C2416

































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды