Samsung S3C2416 Скачать руководство пользователя страница 109

Страница: 109 / 672

S3C2416X RISC MICROPROCESSOR

SYSTEM

CONTROLLER

2-31

8.3 POWER

MANAGEMENT

REGISTERS (PWRMODE AND PWRCFG)

If you want to change the power management mode, you just write a bit(s) into PWRMODE register. Before

writing, you must configure condition to wake-up from the power down mode.

Register

Address

R/W

Description

Reset Value

PWRMODE

0x4C00_0040

R/W

Power mode control register

0x0000_0000

PWRCFG 0x4C00_0060

R/W

Power

management configuration register

0x0000_0000

S3C2416 consists of three power-down modes, which are IDLE, (Deep)STOP, and SLEEP. The mode transition

from the NORMAL mode occurs when the appropriate value is written into PWRMODE & PWRCFG register. If

software tries to write illegal value, i.e., tries to set multiple power modes concurrently, then the write operation will

be ignored.

PWRMODE

Bit

Description

Initial Value

RESERVED [31:17]

RESERVED

STOP [16]

The system enters into STOP mode when this field is set to

‘1’.

SLEEP [15:0]

The system enters into SLEEP mode when this field is set to

‘0x2BED’. The bit pattern, ‘0x2BED’, represents “Go To BED”.

PWRCFG register controls the configuration of power mode transition.

PWRCFG

Bit

Description

Initial Value

RESERVED [31:18]

0x0000

STANDBYWFI_EN [17]

Enable entering of IDLE mode by STANDBYWFI.
0 = Disable, 1 = Enable

DEEP-STOP [16]

Enable the system enters DEEP-STOP mode.
If user set 16th register of PWRMODE reg. (ie. STOP) while

this bit is configured to ‘1’, the system enters DEEP-STOP

mode not STOP mode. To enter the DEEP-STOP mode

properly, this bit should be configured prior to setting STOP

mode bit.

SLEEP_CFG [15]

Enable wakeup source
0 = Wakeup sources are enabled depending on BATT_FLT in

sleep mode. If BATT_FLT pin is asserted logic ‘1’ system can

be exit from sleep mode by appropriate wakeup sources. If

not, system continuously remain it’s sleep state.
1 = Enable wakeup sources regardless of BATT_FLT in sleep

mode.

RESERVED [14:10]

0x00

NFRESET_CFG [9]

Reset configuration when internal resets is generated
0 = Reset NAND flash controller.
1 = Do not reset NAND flash controller.

Содержание S3C2416

































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание S3C2416

Отзывы:

Бренды по названию

Популярные бренды

Samsung S3C2416, Руководство пользователя

Результаты поиска

Содержание S3C2416

Отзывы:

Бренды по названию

Популярные бренды