Samson FOUNDATION 3730-5 Скачать руководство пользователя страница 87

Страница: 87 / 128

KH 8384-5 EN

Parameter lists

AO FB:

SHED_OPT (27)

Storage class S; read/write capability r/w; supported modes ALL
Behavior upon exceeding the monitoring time (see SHED_RCAS in the Resource Block)
Monitoring of the connection between fieldbus host system and AO Function Block in RCAS

mode. When the monitoring time has elapsed, AO Function Block switches from the RCAS

mode to the selected operating mode.
The action to be taken after the fault state ends is also determined.

•

[UNINITIALIZED]

•

NORMAL SHED_NORMAL RETURN · On failure of remote connection, change to next

possible mode until RCAS mode is restored.

•

NORMAL SHED_NO RETURN · On failure of remote connection, change to next

possible mode. The block remains in this mode.

•

SHED TO AUTO_NORMAL RETURN · On failure of remote connection, change to AUTO

mode until RCAS mode is restored.

•

SHED TO AUTO_NO RETURN · On failure of remote connection, change to AUTO

mode. No attempt is made to restore the mode and the block remains in AUTO mode.

•

SHED TO MANUAL_NORMAL RETURN · On failure of remote connection, change to

MAN mode until RCAS mode is restored.

•

SHED TO MANUAL_NO RETURN · On failure of remote connection, change to MAN

mode. No attempt is made to restore the mode and the block remains in MAN mode.

•

SHED TO RETAINED TARGET_ NORMAL RETURN · On failure of remote connection, the

block attempts to attain the retained target mode until RCAS mode is restored.

•

SHED TO RETAINED TARGET_NO RETURN · On failure of remote connection, the block

sets the target mode to the retained target mode.

Note:

This parameter is only active in RCAS mode in the AO Function Block.

If the value is set to UNINITIALIZED, the AO Function Block cannot be placed in the RCAS

mode.

AO FB:

SIMULATE (10)

Storage class D; read/write capability r/w; supported modes ALL
Simulation of the process variable PV of the block (value and status)



Code 48 F3

Note:

During simulation, OUT is not transmitted to the Transducer Block; the block retains

the last valid value received before simulation was activated.

The simulation can only be activated when SIMULATE ACTIVE is set in the BLOCK_ERR

parameter of the Resource Block.

Содержание FOUNDATION 3730-5

































































































































Результаты поиска

Содержание FOUNDATION 3730-5

Отзывы:

Samson FOUNDATION 3730-5, Руководство по настройке, Страница: 87 / 128

Результаты поиска

Содержание FOUNDATION 3730-5

Отзывы: