Samson FOUNDATION 3730-5 Скачать руководство пользователя страница 111

Страница: 111 / 128

KH 8384-5 EN

111

Parameter lists

PID FB:

SP_RATE_DN (19)

Storage class S; read/write capability r/w; supported modes ALL
Set point downward rate limit in AUTO mode

• [3402823466 x 10

]

Note:

if '0' is entered, the set point is used. Speed limitation for control blocks is only

active in AUTO mode.

PID FB:

SP_RATE_UP (20)

Storage class S; read/write capability r/w; supported modes ALL
Set point upward rate limit in AUTO mode

• [3402823466 x 10

]

Note:

if '0' is entered, the set point is used. Speed limitation for control blocks is only

active in AUTO mode.

PID FB:

ST_REV (1)

Storage class S; read capability r

Static revision number (PID)

Note:

The revision number is incremented with each change of a static parameter in the

block.

PID FB:

STATUS_OPTS (14)

Storage class S; read/write capability r/w; supported modes O

Status options to determine status handling and processing

•

[UNINITIALIZED]

•

IFS IF BAD IN · Fault state of the downstream AO Function Block is triggered when the

controlled variable IN changes the status to BAD.

•

IFS IF BAD CAS_IN · Fault state of the downstream AO Function Block is triggered when

the external set point CAS_IN changes the status to BAD.

•

USE UNCERTAIN AS GOOD · The UNCERTAIN status is used as GOOD

•

TARGET IN MANUAL IF BAD IN · Transition to MAN mode if the controlled variable

changes the status to BAD

PID FB:

STRATEGY (3)

Storage class S; read/write capability r/w; supported modes ALL

Permits strategic grouping and thus faster processing of blocks

• [0]

Blocks are grouped by entering the same number in the STRATEGY parameter of each

block.

Note:

These data are neither checked nor processed by the PID Function Block.

Содержание FOUNDATION 3730-5

































































































































Результаты поиска

Содержание FOUNDATION 3730-5

Отзывы:

Samson FOUNDATION 3730-5, Руководство по настройке, Страница: 111 / 128

Результаты поиска

Содержание FOUNDATION 3730-5

Отзывы: