Samson FOUNDATION 3730-5 Скачать руководство пользователя страница 29

Страница: 29 / 128

KH 8384-5 EN

Parameter lists

RES:

BLOCK_ERR (6)

Storage class D; read capability r

Active block errors



Code 48 S2

•

SIMULATE ACTIVE · Simulation jumper active, simulation possible

•

OUT OF SERVICE · Block mode is out of service

•

LOST STATIC DATA · Data loss in EEPROM

•

DEVICE NEEDS MAINTENANCE SOON · Maintenance required soon. This message

triggers a block alarm (BLOCK_ALM) in the Resource Block.

•

DEVICE NEEDS MAINTENANCE NOW · Maintenance required now. This message

triggers a block alarm (BLOCK_ALM) in the Resource Block.

Note:

The assignment of error or diagnostic alarms to the desired function block is made

using the ERROR_OPTION parameters in the Transducer Block.

RES:

BUS_ADDRESS (78)

Storage class D; read capability r
Bus address



Code 46

• 0 to 255, [248]

RES:

CLR_FSTATE (30)

Storage class D; read/write capability r/w; supported modes O/A
Deactivation of the fault state of the AO Function Block

RES:

CONDENSED_STATE (81)

Storage class D; read capability r
Displays the current condensed state according to NAMUR Recommendation NE 107

RES:

CONFIRM_TIME (33)

Storage class S; read/write capability r/w; supported modes O/A
Confirmation time for event report
If the device does not receive a confirmation within this period of time, the event report is

sent again.

•

[640000 ms]

RES:

CYCLE_SEL (20)

Storage class S; read/write capability r/w; supported modes O/A
Block execution method determined by the fieldbus host system

• [Scheduled]
•

Block Execution · Block execution completed

•

Manuf Specific · Not analyzed

Note:

The execution method is selected directly in the fieldbus host system.

Содержание FOUNDATION 3730-5

































































































































Результаты поиска

Содержание FOUNDATION 3730-5

Отзывы:

Samson FOUNDATION 3730-5, Руководство по настройке, Страница: 29 / 128

Результаты поиска

Содержание FOUNDATION 3730-5

Отзывы: