Samson FOUNDATION 3730-5 Скачать руководство пользователя страница 66

Страница: 66 / 128

KH 8384-5 EN

Parameter lists

AO TRD: READBACK_SELECT (35)

Storage class S; read/write capability r/w
Select current or actual valve position for the READBACK parameter

•

[FINAL_POSITION_VALUE]

•

WORKING_POS

AO TRD: REFLAUF_VOLLST (177)

Storage class D; read capability r
Reference tests completed

AO TRD: RESET_STATUS_MESSAGE_DIAG (134)

Storage class D; read/write capability r/w

Select reset command

• Single error message
• Trends, histograms, test diagrams
•

PST/FST parameters and measured values

• Logging
• All recorded diagnostic data (except for reference graphs and logging)

AO TRD: SELECT_EMERGENCY_MODE (126)

Storage class S; read/write capability r/w
Behavior upon failure/defective travel sensor

• Open-loop control based on saved characteristic
•

Move to defined fail-safe position

AO TRD: SELO (109)

Storage class S; read/write capability r/w; supported modes O/M/A
Display/change installed options that are not automatically detected (IDENT_LIMIT_

SWITCHES, IDENT_EXT_LEAKAGE_SENSOR, IDENT LEAKAGE DETECTION, IDENT_EXT_

POS_SENSOR)

AO TRD: SET_FAIL_SAFE_POS (114)

Storage class S; read/write capability r/w

Set fail-safe position

•

NOT ACTIVE

•

SET FAIL-SAFE POSITION

•

CLEAR FAIL-SAFE POSITION

Note:

The fail-safe position is indicated on the positioner display by a blinking 'S'.

Содержание FOUNDATION 3730-5

































































































































Результаты поиска

Содержание FOUNDATION 3730-5

Отзывы:

Samson FOUNDATION 3730-5, Руководство по настройке, Страница: 66 / 128

Результаты поиска

Содержание FOUNDATION 3730-5

Отзывы: