manualshive.com logo in svg

Samson FOUNDATION 3730-5, Руководство по настройке, Страница: 15 / 128

Поделиться
Скачать
Samson FOUNDATION 3730-5 Скачать руководство пользователя страница 15

KH 8384-5 EN 

 15 

Status classification and condensed state

6 

Status classification and condensed state

All status messages are classified in the positioner to report an error that has occurred. The 
status classification can be changed over the DIAG_CLS parameter.
To provide a better overview, the classified messages are summarized in a condensed state 
(CONDENSED_STATE (81) in the Resource Block). Besides the CONDENSED_STATE parame

-

ter, the condensed state can be issued to the discrete output OUT_D of the DI Function Blocks 
(DI1 + DI2).

Possible condensed states include:

0

OK

1

Maintenance required The positioner still performs its control task (with restrictions). A 

maintenance demand or above average wear has been determined.
The wear tolerance will soon be exhausted or is reducing at a faster 

rate than expected. Maintenance is necessary in the medium term.

2

Maintenance 

demanded

The positioner still performs its control task (with restrictions). A 

maintenance demand or above average wear has been determined.
The wear tolerance will soon be exhausted or is reducing at a faster 

rate than expected. Maintenance is necessary in the short term.

3

Maintenance alarm

The positioner cannot perform its control task due to a functional fault 

in the positioner itself or in one of its peripherals or an initialization has 

not yet been successfully completed.

7

Function check

Test or calibration procedures are performed in the positioner. The 

positioner is temporarily unable to perform its control task as long as 

the procedure is taking place.

7 

Block model

Several parameters can only be changed in certain modes (see Read/write capability in the 

parameter description). In this case, not the actual mode is decisive, but the target mode.

7.1 

Resource Block (RES)

The Resource Block contains all the data that identify the device. It is similar to an electronic 
device tag. Resource Block parameters include device type, device name, manufacturer ID, 

serial number as well as parameters that affect the behavior of all other blocks of the device.

Содержание FOUNDATION 3730-5

































































































































Отзывы:

Нет отзывов