Saadat Respina P1 Скачать руководство пользователя страница 54

Страница: 54 / 107

The power supply alarms include:

Ventilator reaction to alarm

Alarm Definition

High Priority

Alarm

Ventilation continues.

Internal battery voltage is lower than
20%.

Battery Low

If the device is connected to the mains
power, ventilation continues.

The internal battery is not available.

No Battery

If the device is connected to the mains
power, ventilation continues.

The battery failure.

Battery Deffect

Ventilator reaction to alarm

Alarm Definition

Medium Priority

Alarm

Ventilation continues.

Internal battery voltage is lower than
20- 40%.

Battery Low

Ventilation continues by using
internal battery.

The device is unplugged.

AC Unplug

Definition

Technical messages

Inspiratory Hold maneuver has been enabled.

Insp.Hold

Expiratory Hold maneuver has been enabled.

Exp.Hold

Manual Ispiratory maneuver has been enabled.

Manual Insp.

100% O2 is delivered to the patient.

O2 100%

Nebulizer has been enabled.

Nebulizer

The suction maneuver has been enabled.

Suction

Apnea backup has been disabled in PSV, VSV and APRV modes.

Apnea off

Warning

Announcing Oxygen related alarms have a delay about 40 seconds.

The disconnection alarm may not be activated if the endotracheal tube is
disconnected from the patient.

Содержание Respina P1












































































































Результаты поиска

Содержание Respina P1

Отзывы:

Бренды по названию

Популярные бренды

Saadat Respina P1, Руководство пользователя

Результаты поиска

Содержание Respina P1

Отзывы:

Бренды по названию

Популярные бренды