manualshive.com logo in svg

Saadat Respina P1, Руководство пользователя

Поделиться
Скачать
Saadat Respina P1 Скачать руководство пользователя страница 51

51 

 

 

Ventilation continues.

 

The oxygen inlet pressure is more 
than the specified level.

 

High O2 Pressure

 

If the Air source is available, 
ventilation continues with Air only. 
The safety valve opens if the pressure 
of both Air and Oxygen sources drops 
or disconnects.

 

The oxygen inlet pressure is lower 
than the specified level. 
This alarm will not be enabled if the 
oxygen concentration is set to 21%. 

 

Low O2 Pressure

 

Ventilation continues.

 

The air inlet pressure is more than 
the specified level.

 

High Air Pressure

 

If the Oxygen source is available, 
ventilation continues with Oxygen 
only. 
The safety valve opens if the pressure 
of both Air and Oxygen sources drops 
or disconnects.

 

The air inlet pressure is lower than 
the specified level. 
This alarm will not be enabled if the 
oxygen concentration is set to 100%.

 

Low Air Pressure

 

Ventilation continues. 

If the measured gas temperature 
parameter (gas temp) exceeds the 
allowed limit (45 ° C). 

High Gas 
Temperature 

Ventilation continues. 

-- 

Error code 17 

Ventilation continues. 

-- 

Error code 2 

Ventilation continues with the 
following settings: Mode: PCV, Rate: 
15, Ti: 1, PEEP: 2, Pcontrol: 20, 
Trigger: Pressure, Ptrig: -3, O2: 100 

-- 

Fatal Error 5 

Ventilation continues with the 
following setting: Mode: PCV, Rate: 
15, Ti: 1, PEEP: 2, Pcontrol: 15, 
Trigger: Pressure, Ptrig: -3, O2: 100 

-- 

Fatal Error 6 

Ventilator reaction to alarm

 

Alarm Definition

 

Medium Priority 

Alarm

 

Ventilation continues.

 

Respiratory rate (including 
spontaneous and mandatory breaths) 
has exceeded high alarm setting in 
three respiratory cycles. 

 

High Rate

 

Ventilation continues.

 

Respiratory rate (including 
spontaneous and mandatory breaths) 
has violated low alarm setting in 
three respiratory cycles. 

 

Low Rate

 

The inhalation phase will switch to 
the exhalation phase (whether alarm 
is activated or not) once Vti has 
exceeded alarm limit.

 

Inspired tidal volume has exceeded 
high alarm setting in three 
consecutive respiratory cycles. 

 

Vti Limit Reached

 

Ventilation continues. 

Exhaled tidal volume has exceeded 
high Vt

e

 alarm setting in three 

consecutive respiratory cycles. 

High Vte 

Содержание Respina P1












































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды