Saadat Respina P1 Скачать руководство пользователя страница 105

Страница: 105 / 107

105

Alarm Message

Possible Cause

Corrective Action

AC Unplug

The device is unplugged.

- Plug in the device.

Battery Defect

The battery failure

Contact the Customer Service
department.

No Battery

The internal battery is not available.

- Ensure that a correct battery has
been inserted in the device.
- If the alarm persists, contact the
Customer Service department.

Error code XX

- Contact the Customer Service
department.

Fatal Error X

- Contact the Customer Service
department.

100% O2 Not

Usable

High pressure oxygen source (higher
than 1,2 bar) is not available.

Check the inlet oxygen source
pressure.

Neb. Not Usable

Flow setting is lower than 11L/min.
High pressure oxygen source is not
available.
The oxygen source pressure is out of
range and the nebulizer will not
activate.

Check that flow is not higher than
11L/min.
Check the inlet oxygen source
pressure.

Suction Not Usable

-The device is in the NIV mode.
- 100% O2 key is pressed before
selecting the suction maneuver.
- “Low O2 Pressure” alarm is active.

- Disable the NIV mode.
- Stop 100% O2 phse.
- Check pressure of the oxygen
source.

Содержание Respina P1












































































































Результаты поиска

Содержание Respina P1

Отзывы:

Бренды по названию

Популярные бренды

Saadat Respina P1, Руководство пользователя

Результаты поиска

Содержание Respina P1

Отзывы:

Бренды по названию

Популярные бренды