Saadat Respina P1 Скачать руководство пользователя страница 15

Страница: 15 / 107

Parts of the device that have high

temperature

Authorized representative of Europe

Warning!

Refer to the device manual

Device weight

Lock and unlock the exhalation valve

Battery location

Indicates that the ventilator is On

Alarm active indicator

Indicates the ventilator running on the

battery and the battery charge status

Indicates the ventilator connection to the

mains power and the battery charging

Lock/Unlock key of touch screen

1-6

Guarantee and responsibilities

The manufacturer will not take any responsibility if operator:



misuses the device



fails to follow operating instructions



disregards any warning or technical information



modifies the device in any way



uses accessories that are not approved or recommended by manufacturer

Содержание Respina P1












































































































Результаты поиска

Содержание Respina P1

Отзывы:

Бренды по названию

Популярные бренды

Saadat Respina P1, Руководство пользователя

Результаты поиска

Содержание Respina P1

Отзывы:

Бренды по названию

Популярные бренды