Rosemount 3107 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 148

background image

Reference Manual

00809-0200-4841, Rev BA

Section 3: Installation

December 2014

Section 3: Installation

10

4.

To avoid detecting unwanted objects in the tank or well, it is advisable to maintain a
distance of at least 1.3 in. from the center line of the transmitter for every foot (11 cm
per meter) range to the obstruction.

5.

No false echoes are generated if the transmitter is located near the side of the tank or
well, and the wall is smooth and free of protrusions. However, there will still be a
reduction in the echo size. It is recommended that the transmitter be mounted no
closer than 12 in. (0,3 m) to the wall to avoid a large reduction in the echo size.

6.

If the transmitter is mounted in an enclosed tank with a domed top, avoid mounting
the transmitter in the center of the tank roof because this could act as a parabolic
reflector and create unwanted echoes.

7.

Avoid applications where heavy condensation could form on the transmitter face.

8.

If the transmitter is mounted in a stand-off or nozzle, the transmitter face should
protrude at least 0.2 in. (5 mm) into the tank.

9.

If the transmitter is used in environments where direct sunlight can cause high surface
temperatures on exposed instruments, a sun-shade is recommended.

Figure 3-2. Considerations when installing in a tank

A. Transmitter is mounted vertically (maximum deviation of 3°).
B. 6° beam half angle.
C. 1.3 in./ft. (11 cm/m). Minimum of 12 in. (0.3 m).

A

C

B

«
...
18
19
20
21
22
...
»

Содержание 3107





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для 3107

Бренд: Nautel Страницы: 224

Бренд: Dolphin Страницы: 17

Бренд: Spotwave Страницы: 2

Бренд: Comet Страницы: 18

PASCAL Ci4 LEVEL

Бренд: Labom Страницы: 35

Бренд: Endress+Hauser Страницы: 8

Бренд: Adeunis RF Страницы: 9

Бренд: Dini Argeo Страницы: 60

Бренд: Nagano Keiki Страницы: 12

Бренд: Farho Страницы: 4

Бренд: SRT Страницы: 76

Бренд: WIKA Страницы: 64

DCCFMT50UD - Car FM Stereo Transmitter

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 2

AIR-SA17Ti Marketing

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 11

Бренд: Sony Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды