Rosemount 3107 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 148

background image

Reference Manual

00809-0200-4841, Rev BA

Section 3: Installation

December 2014

Section 3: Installation

8

3.2

Considerations before installation

The Rosemount 3107 and 3108 may be used for level and volume measurement in open or
closed tanks, or open channel flow measurement.

The transmitter must be installed in a location where it is protected from ultraviolet radiation to
prevent long term degradation of the plastics used in its construction e.g. shrouded from direct
sunlight.

It is important to correctly position the transmitter for reliable ultrasonic level measurement.
For maximum accuracy and stability of the level measurement reading, the transmitter should
always be shrouded from direct sunlight and radiated heat.

The transmitter may be site-tuned to deal with most application conditions, but it is
recommended that the following guidelines be adopted wherever relevant.

3.2.1

Safety considerations

Guidelines

1.

Installation must be carried out by suitably trained personnel in accordance with the
applicable code of practice.

2.

If the equipment is likely to come into contact with

aggressive substances

, it is the

responsibility of the user to take

suitable precautions

that prevent it from being

adversely affected, thus ensuring that the type of protection is not compromised.

Aggressive substances are acidic liquids or gases that may attack metals or solvents
that may affect polymeric materials.

Suitable precautions are regular checks as part of routine inspections, or establishing,
from the material's datasheet, that it is resistant to specific chemicals.

3.

The equipment should only be cleaned with a damp cloth. Do not use solvents.

4.

The equipment is not intended to be repaired by the user and is to be replaced by an
equivalent certified unit. Repairs should only be carried out by the manufacturer or
approved repairer.

5.

The transmitter is

Double Insulated

, and therefore Protective Earthing is not required.

6.

Note that if the equipment is used in a manner not specified by the manufacturer, the
protection afforded by the equipment may be impaired.

7.

To ensure electro-magnetic compatibility in any European member state, it should not
be installed in a residential area.

Note



It is not advisable to mount the transmitter in close proximity to a source of electrical
noise such as a variable-speed drive, or other high-powered electrical device.

«
...
16
17
18
19
20
...
»

Содержание 3107





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для 3107

Beolab transmitter 1

Бренд: Bang & Olufsen Страницы: 30

Бренд: M-system Страницы: 3

Бренд: Magnetrol Страницы: 16

Бренд: Tactic Страницы: 2

Бренд: Icom Страницы: 42

Бренд: Icom Страницы: 6

Бренд: Alinco Страницы: 16

Бренд: Icom Страницы: 147

TWOMOBILE MK II

Бренд: GAREX Страницы: 18

Бренд: M-system Страницы: 5

THERMASGARD ETM 5

Бренд: S+S Regeltechnik Страницы: 16

Бренд: ADTRAN Страницы: 2

Бренд: ADTRAN Страницы: 2

Combo PON D2 SFP+

Бренд: ADTRAN Страницы: 4

Бренд: Kenwood Страницы: 44

Бренд: Kenwood Страницы: 26

Бренд: Kenwood Страницы: 28

Бренд: Kenwood Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды