Roland SR-20HD, Справочное руководство

Страница: 55 / 70

55
Menu List
Menu item Value
(Bold: default)
Explanation
LINE IN
Adjusts the audio that is input from the AUDIO IN 5/L, 6/R (LINE IN) jacks.
Digital Gain
-42.0– 0.0 – 42.0 dB
Adjusts the input gain (sensitivity) in the digital domain (after conversion from analog to
digital).
Level
-INF , -80.0–10.0 dB Adjusts the input volume.
Phase
Off , On Reverses the phase of the audio signal.
MAIN Mute
Off , On
Turns the mute function on/off.
If this is set to ”On”, the input audio to MAIN bus is temporarily muted.
Monitor Mute
Off , On
Turns the mute function on/off.
If this is set to ”On” the input audio to Monitor bus is temporarily muted.
REC Send
-INF , -80.0–10.0 dB Adjusts the amount of audio sent to the REC bus.
HPF 75 Hz
Off
, On
Turns the high-pass filter on/off. Cuts off low-band audio not required for the effect.
The cutoff frequency is 75 Hz.
EQ
Off , On
Turns the equalizer on/off.
Adjusts the volume for each frequency band.
Mid Gain -15.0–
0.0
–+15.0 dB Boosts or attenuates the midrange band.
Mid Freq 20.0 Hz–
500 Hz
–20.0 kHz Adjusts the center frequency when changing the volume in the midrange band.
Mid Q 0.5,
1.0
, 2.0, 4.0, 8.0, 16.0 Adjusts the frequency bandwidth when boosting or attenuating the midrange band.
Lo Gain -15.0–
0.0
–+15.0 dB Boosts or attenuates the low band.
Lo Freq 20.0 Hz–
100 Hz
–2.0 kHz Adjusts the center frequency when changing the volume in the low band.
Hi Gain -15.0–
0.0
–+15.0 dB Boosts or attenuates the high band.
Hi Freq 1.0–
10.0
–20.0 kHz Adjusts the center frequency when changing the volume in the high band.
HEADSET Mic
Adjusts the audio that is input from the HEADSET (headset mic) jacks.
Analog Gain -10– -28– -52 dBu Adjusts the input gain (sensitivity) in the analog domain.
Digital Gain
-42.0–
0.0
–42.0 dB
Adjusts the input gain (sensitivity) in the digital domain (after conversion from analog to
digital).
Level
-INF, -80.0– 0.0 –10.0 dB Adjusts the input volume.
Phase
Off , On Reverses the phase of the audio signal.
MAIN Mute
Off, On
Turns the mute function on/off.
If this is set to ”On”, the input audio to MAIN bus is temporarily muted.
Monitor Mute
Off,
On
Turns the mute function on/off.
If this is set to ”On” the input audio to Monitor bus is temporarily muted.
REC Send
-INF , -80.0–10.0 dB Adjusts the amount of audio sent to the REC bus.
Pan
L50–L1, Center , R1–R50 Adjusts the stereo position (pan).
HPF 75 Hz
Off , On
Turns the high-pass filter on/off. Cuts off low-band audio not required for the effect.
The cutoff frequency is 75 Hz.
Gate
Off , On
Turns the noise gate on/off.
Eliminates audio that is lower than the specified threshold level.
Threshold
-80–
-50
–0 dB
Specifies the base level used as the threshold for removing audio.
Audio below the level set here is removed.
Release
30– 860 –5000 ms
Adjusts the length of time until the audio is fully attenuated after the audio level falls below
the threshold.
Compressor
Off
, On
Turns the compressor on/off.
Audio that exceeds the specified effect threshold level is compressed.
Threshold
-50– -8 –0 dB
Specifies the base level at which the compressor is applied.
Compression is applied to audio that exceeds the threshold.
Ratio
1.00:1, 1.12:1, 1.25:1, 1.40:1, 1.60:1,
1.80:1, 2.00:1, 2.50:1 , 3.20:1,
4.00:1, 5.60:1, 8.00:1, 16.0:1, INF:1
Specifies the degree of compression applied to the audio.
The state in which no compression is applied is defined as “1”.
Attack
0– 3.0 –100 ms Specifies the time until compression starts when audio exceeding the threshold is input.
Release
30– 250 –5000 ms Adjusts the length of time until compression ends after audio falls below the threshold.
Makeup Gain
-40– 0 –40 dB Adjusts the final output volume level after applying the compressor.