manualshive.com logo in svg

RKI Instruments 03 Series, Руководство оператора

Поделиться
Скачать
RKI Instruments 03 Series Скачать руководство пользователя страница 72

 

67 • Maintenance

03 Series Operator’s Manual

5. Remove the front case from the rear case.

Figure 15: Case Separation

6. Carefully remove the old sensor from the sensor socket. 

7. Carefully insert the replacement sensor in the socket. Make sure the 

sensor face with the colored ring is facing up and that the sensor is 
keyed correctly (HS-03 and CO-03 only).

Figure 16: Replacing the Sensor

CAUTION: When replacing the sensor, verify that the sensor is properly 

aligned with its socket before inserting it into the socket. The 
CO and H

2

S sensors have alignment slots which match up 

with alignment tabs in the sockets. Forcing a sensor into its 
socket may damage the sensor or the socket.

Front Case

Rear Case

Screw, 4x

Tabs

Oxygen 

Sensor

H2S 

Sensor

CO 

Sensor

Align Slots in H2S 
and CO Sensor 
with Tabs in Case

Oxygen 
Sensor Not 
Keyed

Rear 

Case

Содержание 03 Series













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды