manualshive.com logo in svg

RKI Instruments 03 Series, Руководство оператора

Поделиться
Скачать
RKI Instruments 03 Series Скачать руководство пользователя страница 15

 

03 Series Operator’s Manual

Start Up • 10

Start Up

This section explains how to start up the 03 Series and to get it ready for 
operation.

NOTE:

The screens shown in this section are for a CO-03. If you are 
using a different version of the 03 Series, your instrument screen 
will vary slightly from those shown below.

Start-up Procedure

1. Press and briefly hold down the POWER MODE button. The backlight 

will turn on and all the display segments will turn on. Release the button 
when you hear a beep.

2. The vibrator vibrates and the alarm light flashes momentarily.

3. The initial startup screen depends on how Bump Fail Behavior is set. 

This parameter along with the Cal. Limit Display and Cal. Limit Check 
parameters mentioned in Step 5 and the Auto Zero Adjustment 
parameter mentioned in Step 12 below cannot be set using the 03 
Series’ instrument menus, but are set using the 03 Series User Setup 
Program. See the 03 Series User Setup Program Operator’s Manual for 
information regarding changing various instrument parameters that are 
not available for adjustment in the instrument’s operating modes.

•

If Bump Fail Behavior is set to None (factory setting) or if it is set to 
Can Not Use

 and the most recently performed bump test passed, 

proceed to Step 5.

•

If Bump Fail Behavior is set to Can Not Use and the most recently 
performed bump test failed, the following screen will appear.

The instrument cannot be used until a successful bump test or 
calibration is performed. See “Calibration Mode” on page 31 for 
instructions.

4. If Cal. Limit Display is set to Off, proceed to Step 6.

 

 
 
 
 

 

 

 

 

 

 

C.AL

FAIL

Содержание 03 Series













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды