manualshive.com logo in svg

RKI Instruments 03 Series, Руководство оператора

Поделиться
Скачать
RKI Instruments 03 Series Скачать руководство пользователя страница 23

 

03 Series Operator’s Manual

Start Up • 18

3. Release the AIR button when the following screen appears. The unit 

will set the reading to 0 ppm (20.9% for the OX-03) and return to 
Measuring Mode.

Turning Off the 03 Series

1. Press and hold the POWER MODE button for about five seconds to 

turn off the unit. The buzzer will pulse while the POWER MODE button 
is being pressed before the unit turns off.

2. Release the button when the LCD is blank. The unit is off.

NOTE:

If Power Off Password Protection is turned On (factory setting is 
Off

) using the 03 Series User Setup Program, a password is 

required to turn the 03 Series off. When the password screen 
appears, adjust each digit with the AIR button and press and 
release the POWER MODE button to move on to the next digit. 
Once the password has been entered, the instrument will shut off 
and the LCD will be blank.

 

 
 
 
 

 

 

 

 

 

 

 

ADJ

 - - - -

Содержание 03 Series













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды