manualshive.com logo in svg

RKI Instruments 03 Series, Руководство оператора

Поделиться
Скачать
RKI Instruments 03 Series Скачать руководство пользователя страница 47

 

03 Series Operator’s Manual

Calibration Mode • 42

3. Press and release the POWER MODE button. The LCD will display the 

current gas readings and “E--CAL.” will flash.

If you want to cancel the calibration, press and hold the AIR key for 2 
seconds. The instrument will return to the E--CAL. Screen. If you hold 
the AIR key down longer than 2 seconds, the instrument will start 
scrolling through the Calibration Mode items.

4. Use the sample tubing to connect the calibration adapter to the 

regulator. Attach the tubing to the calibration adapter on the inlet side as 
shown below in Figure 7.

Figure 7: Calibration Kit Assembly

5. Confirm that the regulator on/off knob is turned all the way clockwise 

(closed) and screw the calibration gas cylinder onto the regulator.

 

 
 
 
 

 

 

 

 

 

G--IN

 

E--CAL.

ppm

0

To Fixed Flow 

Regulator

Calibration 

Adapter

Calibration Tubing

Содержание 03 Series













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды