manualshive.com logo in svg

RKI Instruments 03 Series, Руководство оператора

Поделиться
Скачать
RKI Instruments 03 Series Скачать руководство пользователя страница 27

 

03 Series Operator’s Manual

Operation • 22

5. Press and release the POWER MODE button again to proceed to the 

TWA Screen. The TWA reading will be displayed. 

6. Press and release the POWER MODE button again to proceed to the 

Full Scale Screen. The detection range full scale value is displayed. An 
“L” or an “A” will appear under the full scale value to indicate whether 
the alarms are set to latching (L) or auto-resetting (A). This setting can 
be adjusted using the 03 Series User Setup Program.  

7. Press and release the POWER MODE button again to proceed to the 

Date/Time Screen. The date and time of the instrument is displayed.

8. Press and release the POWER MODE button once again to return the 

unit to Measuring Mode. 

NOTE:

If you do not press a button for 20 seconds while in Display Mode, 
the unit will return to Measuring Mode automatically and the 
backlight will turn off.

Display Mode, OX-03

This section describes Display Mode for the OX-03 only. See “Display 
Mode, CO-03 and HS-03” on page 20 for a description of the CO-03 and 
HS-03 instruments’ Display Mode.

You can access Display Mode while in Measuring Mode by using the 
POWER MODE button. In Display Mode you can view and reset the 
minimum and maximum readings, view the detection range full scale, and 
view the date and time.

 

 
 
 
 

 

 

 

 

 

 

TWA

ppm

10

 

 
 
 
 

 

 

 

 

 

 

F. S.

 

ppm

L

500

 

 
 
 
 

 

 

 

 

 

8:20

 

 

2014

 1.31

 

Содержание 03 Series













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды