manualshive.com logo in svg

RKI Instruments 03 Series, Руководство оператора

Поделиться
Скачать
RKI Instruments 03 Series Скачать руководство пользователя страница 57

 

03 Series Operator’s Manual

Calibration Mode • 52

•

To view the bump test gas reading, press the AIR button.

•

To return to the BUMP screen in Calibration Mode, press POWER 
MODE at any time.

•

Turn the regulator on/off knob clockwise to close it.

If the instrument fails the bump test, 

•

A calibration is immediately and automatically started. The 
instrument will begin a countdown whose length depends on the 
Bump Test Time(sec)

 and Calibration Time(sec) After Bump 

Test Failed

 parameters’ values. These parameters can be changed 

using the 03 Series User Setup Program. The countdown time for 
the calibration is the Calibration Time(sec) After Bump Test 
Failed

 value (factory setting is 90 seconds) minus the Bump Test 

Time(sec)

 value (factory setting is 30 seconds). Continue to apply 

the calibration gas.

 

 
 
 
 

 

 

 

 

 

 

 

BUMP

 

ppm

45

 

 
 
 
 

 

 

 

 

 

 

 

BUMP

 

 

 

 
 
 

 

 

 

 

 

 

 

APPLY

 

ppm

45

60

 

 
 
 

 

 

 

 

 

 

 

CAL.

 

ppm

45

60

Содержание 03 Series













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды