manualshive.com logo in svg

RKI Instruments 03 Series, Руководство оператора

Поделиться
Скачать
RKI Instruments 03 Series Скачать руководство пользователя страница 49

 

03 Series Operator’s Manual

Calibration Mode • 44

adjustment (zero adjustment for OX-03). 

10. If the span adjustment (zero adjustment for OX-03) is successful, the 

LCD will show the following screen before returning to the E--CAL 
screen.

If the Maximum Span setting is turned On (factory setting is Off) using 
the 03 Series User Setup Program, the LCD will show the maximum 
reading the sensor could have been calibrated to before returning to the 
E--CAL screen.

11. If the span adjustment (zero adjustment for OX-03) fails, the LCD will 

show the following screen, the alarm LED will flash, and the buzzer will 
sound a double pulsing tone.

Press and release the POWER MODE button to clear the failure 
indication and return to the E--CAL. screen.

See “Troubleshooting” on page 63 to investigate the cause of the failure 
and replace the failed sensor if necessary.

12. Turn the regulator on/off knob clockwise to close it.

13. Remove the calibration adapter from the instrument.

 

 
 
 
 

 

 

 

 

 

PASS

 

 

 
 
 
 

 

 

 

 

 

 

C--MAX

ppm

75

 

 
 
 
 

 

 

 

 

 

FAIL

 

CO

ppm

 

 
 
 
 

 

 

 

 

 

 

E--CAL.

Содержание 03 Series













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды