manualshive.com logo in svg

RKI Instruments 03 Series, Руководство оператора

Поделиться
Скачать
RKI Instruments 03 Series Скачать руководство пользователя страница 20

 

15 • Start Up

03 Series Operator’s Manual

•

If a bump test is due and Bump Test Limit Check is set to None, 
the sequence below will occur twice. 

Press and release the POWER MODE button during this time to go 
to the BUMP menu item in Calibration Mode. If no button is pressed, 
the instrument will continue with the warmup sequence in Step 8 
once the sequence shown above has finished.

NOTE:

If a successful calibration is performed, the next bump test date is 
reset and starts over even though a bump test was not performed.

•

If bump testing is not due, then the following screen appears for a 
few seconds indicating when the next bump test is due. “NEXT” and 
“BUMP” alternate on the bottom of the screen. 

8. The Date/Time Screen appears for a few seconds.

This screen displays the current date and time.

9. The Battery Voltage Screen appears for a few seconds.

 

 
 
 

 

 

 

 

 

MODE

 

 

BUMP

 

 

 

 
 
 

 

 

 

 

 

YES

 

 

BUMP

 

 

 

 
 
 

 

 

 

 

 

 

 

BUMP

 

0d

0d

0d

 

 
 
 

 

 

 

 

 

BUMP

 

 

14. 2.17

180d

 

 

 
 
 
 

 

 

 

 

 

NEXT

 

 

14. 2.17

180d

 

 

 
 
 
 

 

 

 

 

 

8:20

 

 

2014

 1.31

 

 

 
 
 
 

 

 

 

 

 

 

 

bAtt

 

3.0

V

Содержание 03 Series













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды