Rigol DS 5000C Скачать руководство пользователя страница 81

Страница: 81 / 122

RIGOL

Using Automatic Measurement as the following steps demonstrate:

1. Select the signal channel for measuring. You could select CH1 or CH2 according

to the signal you are interested in.

Press soft buttons as follows: MEASURE

→

Source

→

CH1

CH2

2. To see all measurement value, set the Display All to ON. 18 measurement

parameters will be displayed on the screen.

3. Select parameters page for measuring. You could select voltage or time

parameters pages by pressing soft button as follows: MEASURE

→

Voltage or

time

Voltage1/3

Voltage2/3

…

4. To gain the measured value on the screen. You could select the parameters you

are interested in by pressing the soft button on the right of the menu, and read
the data on the bottom of the screen.

If the data is displayed as “*****”, that means the parameter cannot be
measured in current condition.

5. Clear the measure values: press Clear. Now, all of the auto measure values

disappear from the screen.

Figure 2-54

Clear the display measure parameter

Display 18 measurements

2-55

User Manual for DS5000 Series

Содержание DS 5000C



























































































































Результаты поиска

Содержание DS 5000C

Отзывы:

Rigol DS 5000C, Руководство пользователя, Страница: 81 / 122

Результаты поиска

Содержание DS 5000C

Отзывы: