Rigol DS 5000C Скачать руководство пользователя страница 100

Страница: 100 / 122

RIGOL

Example 6: The application of the X-Y operation

Viewing Phase Changes through a Network

Connect the oscilloscope to monitor the input and output of the circuit and capture
the phase changes through the circuit.

To view the input and output of the circuit in an x-y display, do these steps:

1. Set the probe menu attenuation to 10X. Set the switch to 10X on the probes.

2. Connect the channel 1 probe to the input of the network, and connect the

channel 2 probe to the output.

3. If the channels are not displayed, press the CH1

and CH2 buttons.

4. Press the AUTO button

5. Adjust the vertical SCALE

knob to display approximately the same amplitude

signals on each channel

6. Press the MENU in horizontal control area to display the menu

7. Press the Time Base soft button to select

X-Y

The oscilloscope displays a Lissajous pattern representing the input and output
characteristics of the circuit

8. Adjust the vertical SCALE and POSITION

knobs to display a desirable waveform.

9. Apply the Ellipse method to observe the phase difference between the two

channels.

(See Figure 3-6)

3-8

User Manual for DS5000 Series

Содержание DS 5000C



























































































































Результаты поиска

Содержание DS 5000C

Отзывы:

Rigol DS 5000C, Руководство пользователя, Страница: 100 / 122

Результаты поиска

Содержание DS 5000C

Отзывы: