Rigel 62353 PLUS Скачать руководство пользователя страница 52

Страница: 52 / 85

48 -

Page Rigel Medical

62353+

user Manual V1.4

Press the

button (F1) to obtain the schematic representation of this test:

Warning

– never leave the earth bond, or any other probe attached to any

moving parts.

Warning

– never touch the appliance under test whilst testing is in

progress. Doing so could result in injury due to electric shock and / or
sudden movement of any mechanical parts on the appliance.

Refer to Page 4 for notes on precautions required for compliance with the
relevant safety standards.

Do not exceed the maximum permitted voltage of 30 V AC/DC
with respect to earth potential! Electric Shock danger!

Press

button (F3) to set the Test Duration, and RMS Pass/Fail limit. Use the

arrow keys to highlight and set. Press the

button (F4) when complete. Pressing

the

button (F3) will exit Settings mode without saving changes.

Press the

button (F2) to change the mains polarity.

For both Class I and Class II appliances, connect ALL Patient Connections or Applied
Parts to the Applied Part Module and fit the Appliance mains plug into the EUT outlet.

Содержание 62353 PLUS





















































































Результаты поиска

Содержание 62353 PLUS

Отзывы:

Rigel 62353 PLUS, Инструкция по эксплуатации, Страница: 52 / 85

Результаты поиска

Содержание 62353 PLUS

Отзывы: