Rigel 62353 PLUS Скачать руководство пользователя страница 47

Страница: 47 / 85

43 -

Page Rigel Medical

62353+

user Manual V1.4

4.1.2 Insulation Resistance EUT

This test is applicable to all Class I and Class II equipment, typically used as part of an
IEC test routines.

Press the F1

button to obtain the schematic representation of this test:

Do not exceed the maximum permitted voltage of 30 V AC/DC
with respect to earth potential! Electric Shock danger!

This test is used to verify that the mains supply pins are adequately insulated from earth
(Class I) or the enclosure (Class II).

During this test, up to 500 VDC is applied between the earth pin and both
the live and neutral pins of the appliance mains supply plug.

Press

button (F3) to set the Test Duration, Insulation test voltage (50 / 100 /

250 & 500 VDC) and Pass/Fail limit. Use the up, down, left and right keys to highlight

and set. Press

button (F4) when complete. Pressing

button (F3) will

exit Settings mode without saving changes.

Press the class button (F2) to set the class of the appliance under test. For a class II
appliance the probe symbol will be displayed at the top of the LCD display.

Содержание 62353 PLUS





















































































Результаты поиска

Содержание 62353 PLUS

Отзывы:

Rigel 62353 PLUS, Инструкция по эксплуатации, Страница: 47 / 85

Результаты поиска

Содержание 62353 PLUS

Отзывы: