Ricoh TH-C1 Скачать руководство пользователя страница 28

Страница: 28 / 203

echnical

ulletin

PAGE: 8/15

Model:

Model TH-C1

Date:

2-Jun-05

No.:

RB156003

A: Procedure for adding the spacers to the toner supply drive gear shaft

I. IMPORTANT NOTES BEFORE YOU BEGIN

* Do not touch the surface of the development roller.

* Be very careful not to scratch or damage the surface of the development roller.

* Always keep the development unit flat (horizontal). Do not tip the unit to one side.

This is to prevent toner from leaking out of the unit.

II. MAIN PROCEDURE

1. Remove the development unit from the machine.
2. Pull out the toner cartridge about 70 mm from the development unit.

Important:

Do not pull out the toner cartridge too far. If you do, toner can leak out of the
cartridge (circled in red in the photos).
If this happens, remove the leaked toner.

70mm

Содержание TH-C1












































































































































































































Результаты поиска

Содержание TH-C1

Отзывы:

Похожие инструкции для TH-C1

Бренды по названию

Популярные бренды

Ricoh TH-C1, Технический бюллетень

Результаты поиска

Содержание TH-C1

Отзывы:

Похожие инструкции для TH-C1

Бренды по названию

Популярные бренды