Renesas ZTAT H8S/2357F Скачать руководство пользователя страница 244 | Manualshive

Страница: 244 / 1047

background image

Rev.6.00 Oct.28.2004 page 216

of 1016

REJ09B0138-0600H

Activation by External Request: If an external request (

DREQ

pin) is specified as an activation source, the relevant port

should be set to input mode in advance.

Level sensing or edge sensing can be used for external requests.

External request operation in normal mode (short address mode or full address mode) is described below.

When edge sensing is selected, a 1-byte or 1-word transfer is executed each time a high-to-low transition is detected on the

DREQ

pin. The next transfer may not be performed if the next edge is input before transfer is completed.

When level sensing is selected, the DMAC stands by for a transfer request while the

DREQ

pin is held high. While the

DREQ

pin is held low, transfers continue in succession, with the bus being released each time a byte or word is

transferred. If the

DREQ

pin goes high in the middle of a transfer, the transfer is interrupted and the DMAC stands by for

a transfer request.

Activation by Auto-Request: Auto-request activation is performed by register setting only, and transfer continues to the
end.

With auto-request activation, cycle steal mode or burst mode can be selected.

In cycle steal mode, the DMAC releases the bus to another bus master each time a byte or word is transferred. DMA and
CPU cycles usually alternate.

In burst mode, the DMAC keeps possession of the bus until the end of the transfer, and transfer is performed continuously.

Single Address Mode: The DMAC can operate in dual address mode in which read cycles and write cycles are separate
cycles, or single address mode in which read and write cycles are executed in parallel.

In dual address mode, transfer is performed with the source address and destination address specified separately.

In single address mode, on the other hand, transfer is performed between external space in which either the transfer source
or the transfer destination is specified by an address, and an external device for which selection is performed by means of
the

DACK

strobe, without regard to the address. Figure 7-17 shows the data bus in single address mode.

External
memory

External

device

(Read)

(Write)

RD

HWR

,

LWR

A

23

to A

0

H8S/2357

Group

D

15

to D

0

(high impedance)

DACK

Address bus

Data bus

Figure 7-17 Data Bus in Single Address Mode

«
...
242
243
244
245
246
...
»

Содержание ZTAT H8S/2357F
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ZTAT H8S/2357F

Бренд: 3Com Страницы: 8

Бренд: Data Translation Страницы: 60

Бренд: QSC Страницы: 28

tBOX330-870-FL Series

Бренд: AXIOMTEK Страницы: 2

Бренд: Funkwerk Страницы: 2

Бренд: Freescale Semiconductor Страницы: 921

Kinetic FLT 80 D5/DDC Body

Бренд: EK-Quantum Страницы: 16

DesignCore RVP-TDA3 Series

Бренд: D3 Страницы: 34

Бренд: Lanner Страницы: 78

Бренд: Z3 Technology Страницы: 87

2000 IDU Series

Бренд: EMS Страницы: 52

HFisolator 9730/26-11

Бренд: Stahl Страницы: 2

Бренд: Matrix Switch Corporation Страницы: 48

SRCSASPH16I - RAID Controller

Бренд: Intel Страницы: 28

Бренд: VIA Technologies Страницы: 2

ibaBM-FOX-i-3o-D

Бренд: IBA Страницы: 13

Бренд: Quantum Страницы: 140

Бренд: JETWAY Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды