Renesas Single-Chip Microcomputer SH7203 страница 37 Скачать руководство пользователя

Страница: 37 / 1622

Section 1

Overview

Rev. 0.50 May 18, 2006 Page 7 of 1588

REJ09B0313-0050

Items Specification

AND/NAND flash
memory controller
(FLCTL)

•

Direct-connected memory interface with AND-/NAND-type flash
memory

•

Read/write in sectors

•

Two types of transfer modes: Command access mode and sector
access mode (512-byte data + 16-byte management code: with ECC)

•

Interrupt request and DMAC transfer request

•

Supports up to 4 Gbits of flash memory

USB2.0 host/function
module (USB)

•

Conforms to the Universal Serial Bus Specification Revision 2.0

•

480-Mbps and 12-Mbps transfer rates provided

•

Can be used as function

•

Software setting supported

•

On-chip 8-Kbyte RAM as communication buffers

LCD controller (LCDC)

•

From 16

1 to 1024

1024 dots supported



8 bpp (bit per pixel): 640

480 max.



16 bpp (bit per pixel): 400

240 max.

•

Supports 4/8/15/16-bpp color modes

•

Supports 1/2/4/6-bpp gray scale modes

•

TFT/DSTN/STN panels supported

•

Signal polarity setting function

•

24-bit color pallet memory (16 of the 24 bits are valid; R:5/G:6/B:5)

•

Unified graphics memory architecture

I/O ports

•

82 I/Os, 16 inputs, and 1 output

•

Input or output can be selected for each bit

•

Internal weak keeper circuit

A/D converter (ADC)

•

10-bit resolution

•

Eight input channels

•

A/D conversion request by the external trigger or timer trigger

D/A converter (DAC)

•

8-bit resolution

•

Two output channels

User break controller
(UBC)

•

Two break channels

•

Addresses, data values, type of access, and data size can all be set

as break conditions

User debugging
interface (H-UDI)

•

E10A emulator support

•

JTAG-standard pin assignment

Содержание Single-Chip Microcomputer SH7203























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Single-Chip Microcomputer SH7203

Отзывы:

Похожие инструкции для Single-Chip Microcomputer SH7203

Бренды по названию

Популярные бренды

Renesas Single-Chip Microcomputer SH7203, Руководство по оборудованию

Результаты поиска

Содержание Single-Chip Microcomputer SH7203

Отзывы:

Похожие инструкции для Single-Chip Microcomputer SH7203

Бренды по названию

Популярные бренды