Renesas Single-Chip Microcomputer SH7203 Скачать руководство пользователя страница 120

Страница: 120 / 1622

Section 4 Clock Pulse Generator (CPG)

Rev. 0.50 May 18, 2006 Page 90 of 1588

REJ09B0313-0050

2. The frequency of the peripheral clock is as follows:

In mode 0

the frequency on the EXTAL pin

the frequency-multiplier of the PLL

circuit

the divisor of the divider 1

In mode 1

(the frequency on the EXTAL pin

1/2)

the frequency-multiplier of

the PLL circuit

the divisor of the divider 1

In mode 2

(the frequency on the CKIO pin

1/4)

the frequency-multiplier of

the PLL circuit

the divisor of the divider 1

In mode 3

(the frequency on the USB_X1 pin

1/4)

the frequency-multiplier of

the PLL circuit

the divisor of the divider 1

The frequency of the peripheral clock should be set to 33.33 MHz or less, and should
not be set higher than the frequency on the CKIO pin.

3. The frequency multiplier of PLL circuit can be selected as

12 or

16. The

divisor of the divider can be selected as

1/2,

1/3,

1/4,

1/6,

1/8, or

1/12. The settings are made in the frequency-control register (FRQCR).

4. The output frequency of the PLL circuit is as follows:

In mode 0

the frequency on the EXTAL pin

the frequency-multiplier of the PLL

circuit

In mode 1

(the frequency on the EXTAL pin

1/2)

the frequency-multiplier of

the PLL circuit

In mode 2/3 (the frequency on the CKIO pin or the USB_X1 pin

1/4)

the frequency-multiplier of the PLL circuit

Ensure that the output frequency of the PLL circuit should be 200 MHz or less.

Содержание Single-Chip Microcomputer SH7203























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Single-Chip Microcomputer SH7203

Отзывы:

Renesas Single-Chip Microcomputer SH7203, Руководство по оборудованию, Страница: 120 / 1622

Результаты поиска

Содержание Single-Chip Microcomputer SH7203

Отзывы: