Renesas Single-Chip Microcomputer SH7203 страница 201 Скачать руководство пользователя | Manualshive

Страница: 201 / 1622

background image

Section 7 User Break Controller (UBC)

Rev. 0.50 May 18, 2006 Page 171 of 1588

REJ09B0313-0050

Section 7 User Break Controller (UBC)

The user break controller (UBC) provides functions that simplify program debugging. These
functions make it easy to design an effective self-monitoring debugger, enabling the chip to debug
programs without using an in-circuit emulator. Instruction fetch or data read/write (bus cycle
(CPU or DMAC) selection in the case of data read/write), data size, data contents, address value,
and stop timing in the case of instruction fetch are break conditions that can be set in the UBC.
Since this LSI uses a Harvard architecture, instruction fetch on the CPU bus (C bus) is performed
by issuing bus cycles on the instruction fetch bus (F bus), and data access on the C bus is
performed by issuing bus cycles on the memory access bus (M bus). The internal bus (I bus)
consists of the internal CPU bus, on which the CPU issues bus cycles, and the internal DMA bus,
on which the DMA issues bus cycles. The UBC monitors the C bus and I bus.

7.1 Features

1. The following break comparison conditions can be set.

Number of break channels: two channels (channels 0 and 1)

User break can be requested as the independent condition on channels 0 and 1.



Address

Comparison of the 32-bit address is maskable in 1-bit units.

One of the four address buses (F address bus (FAB), M address bus (MAB), internal CPU
address bus (ICAB), and internal DMA address bus (IDAB)) can be selected.



Data

Comparison of the 32-bit data is maskable in 1-bit units.

One of the three data buses (M data bus (MDB), internal CPU data bus (ICDB), and
internal DMA data bus (IDDB)) can be selected.



Bus selection when I bus is selected

Internal CPU bus or internal DMA bus



Bus cycle

Instruction fetch (only when C bus is selected) or data access



Read/write



Operand size

Byte, word, and longword

2. In an instruction fetch cycle, it can be selected whether the start of user break interrupt

exception processing is set before or after an instruction is executed.

3. When a break condition is satisfied, a trigger signal is output from the

UBCTRG

pin.

«
...
199
200
201
202
203
...
»

Содержание Single-Chip Microcomputer SH7203























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Single-Chip Microcomputer SH7203

Бренд: Data Translation Страницы: 60

ILDA Gem Laser projector tool

Бренд: Stanwax Laser Страницы: 3

FieldPoint cFP-RTD-122

Бренд: National Instruments Страницы: 15

Бренд: Parker Страницы: 50

Бренд: Juniper Страницы: 7

Бренд: Lutron Electronics Страницы: 4

Бренд: Giacomini Страницы: 2

Бренд: IBM Страницы: 64

Бренд: Bailey Страницы: 33

CL-SOM-AM57 Series

Бренд: CompuLab Страницы: 79

Бренд: Renesas Страницы: 40

Modular Fast Fiber Switch Converter MT-RJ

Бренд: Lindy Страницы: 3

Бренд: Mod Страницы: 11

Бренд: IBA Страницы: 36

Бренд: Datalogic Страницы: 2

EK-TIM Indigo Extreme

Бренд: ekwb Страницы: 4

Бренд: Hakki Pilke Страницы: 48

Бренд: Acqiris Страницы: 89

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды