manualshive.com logo in svg

Renesas Single-Chip Microcomputer SH7203, Руководство по оборудованию

Микроконтроллер Renesas Single-Chip Microcomputer SH7203 обеспечивает высокую производительность и надежность. Скачайте бесплатное руководство по аппаратному обеспечению на manualshive.com для более эффективного использования устройства. Углубитесь в функциональные возможности этого удивительного продукта и настройте его по своему усмотрению.

Поделиться
Скачать
background image

Section 23   USB 2.0 Host/Function Module (USB) 

Rev. 0.50  May 18, 2006  Page 1154 of 1588 

REJ09B0313-0050 

 

(5)  Control Transfer Stage Transition Interrupt 

Figure 23.7 shows a diagram of how this module handles the control transfer stage transition. This 
module controls the control transfer sequence and generates control transfer stage transition 
interrupts. Control transfer stage transition interrupts can be enabled or disabled individually using 
INTENB0. The transfer stage that made a transition can be confirmed using the CTSQ bit in 
INTSTS0. 

The control transfer sequence errors are described below. If an error occurs, the PID bit in 
DCPCTR is set to B'1x (STALL). 

1.  During control read transfers 

 

At the IN token of the data stage, an OUT or PING token is received when there have been 
no data transfers at all. 

 

An IN token is received at the status stage 

 

A packet is received at the status stage for which the data packet is DATAPID = DATA0 

2.  During control write transfers 

 

At the OUT token of the data stage, an IN token is received when there have been no ACK 
response at all 

 

A packet is received at the data stage for which the first data packet is DATAPID = 
DATA0 

 

At the status stage, an OUT or PING token is received 

3.  During no-data control transfers 

 

At the status stage, an OUT or PING token is received 

 

At the control write transfer stage, if the number of receive data exceeds the wLength value of the 
USB request, it cannot be recognized as a control transfer sequence error. At the control read 
transfer status stage, packets other than zero-length packets are received by an ACK response and 
the transfer ends normally. 

When a CTRT interrupt occurs in response to a sequence error (SERR = 1), the CTSQ = 110 value 
is retained until CTRT = 0 is written from the system (the interrupt status is cleared). Therefore, 
while CTSQ = 110 is being held, the CTRT interrupt that ends the setup stage will not be 
generated even if a new USB request is received. (This module retains the setup stage end, and 
after the interrupt status has been cleared by software, a setup stage end interrupt is generated.) 

Содержание Single-Chip Microcomputer SH7203























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Single-Chip Microcomputer SH7203

IBM LS42 - BladeCenter - 7902 Installation Manual preview
LS42 - BladeCenter - 7902
Бренд: IBM Страницы: 56
IBM ATA 133 Quick Hardware Setup Manual preview
ATA 133
Бренд: IBM Страницы: 2
IBM BladeCenter Management Module User Manual preview
BladeCenter Management Module
Бренд: IBM Страницы: 78
IBM 9040-MR9 Manual preview
9040-MR9
Бренд: IBM Страницы: 110
IBM Remote Supervisor Adapter II User Manual preview
Remote Supervisor Adapter II
Бренд: IBM Страницы: 132
National Instruments NI 9213 Getting Started preview
NI 9213
Бренд: National Instruments Страницы: 11
IBM 3101 Maintenance Information preview
3101
Бренд: IBM Страницы: 63
CAP-XX Purpose User Manual preview
Purpose
Бренд: CAP-XX Страницы: 8
Tektronix CTS 850 User Manual preview
CTS 850
Бренд: Tektronix Страницы: 178
RAIDAGE DAGE312UTL-NAS User Manual preview
DAGE312UTL-NAS
Бренд: RAIDAGE Страницы: 60
Kramer RK-10MT Quick Start Manual preview
RK-10MT
Бренд: Kramer Страницы: 2
GarrettCom Industrial Network Track OSI Brochure preview
Industrial Network Track OSI
Бренд: GarrettCom Страницы: 10
Adaptec 2410SA - Serial ATA RAID Controller Hardware Installation Manual preview
2410SA - Serial ATA RAID Controller
Бренд: Adaptec Страницы: 14
Navitar 1-62643 Dimensional Drawing preview
1-62643
Бренд: Navitar Страницы: 1
audemat DIGIPLEXER 246 User Manual preview
DIGIPLEXER 246
Бренд: audemat Страницы: 93
StetSom STX2448 User Manual preview
STX2448
Бренд: StetSom Страницы: 18
Intel MCS48 User Manual preview
MCS48
Бренд: Intel Страницы: 469
Magtek IntelliStripe 65 Technical Reference Manual preview
IntelliStripe 65
Бренд: Magtek Страницы: 44

Бренды по названию

Популярные бренды

Загрузить еще бренды