manualshive.com logo in svg

Redback Networks SmartEdge 100, Руководство по оборудованию

Поделиться
Скачать
Redback Networks SmartEdge 100 Скачать руководство пользователя страница 35

Installing the Hardware

4-1

C h a p t e r   4

Installing the Hardware

This chapter describes how to install the SmartEdge

®

100 router hardware, including the SmartEdge 100 

chassis and its Fast Ethernet (FE) and Gigabit Ethernet (GE) media interface cards (MICs), how to mount 
the chassis, connect the power cables, complete the installation, and connect and route the cables. The 
sequence of tasks to install the hardware is:

1. Getting Started

2. Mounting the Chassis 

3. Connecting the Power Cables

4. Completing the Installation

5. Connecting and Routing the Cables

When you have finished installing the hardware, you are ready to check the operational status. Checking 
the operational status is described in Chapter 5, “Determining Operating Status.” 

Getting Started

Before you perform the tasks described in this chapter, ensure that you have:

1. Selected the installation site for the chassis; see the “Planning the Site and Installation” section in 

Chapter 3, “Preparing for Installation.” Review the site and installation considerations that are listed 
later in this section.

2. Unpacked and inventoried the SmartEdge 100 chassis and associated hardware and documentation; see 

the 

SmartEdge 100 System Unpacking Instructions

 publication.

3. Selected the type of access for commissioning and normal operations; see the “Selecting the Type of 

Management Access” section in Chapter 3, “Preparing for Installation.”

4. Gathered all cables and tools needed for the installation; see Table 4-1. 

Note

The term, GE, applies to any GE native port or MIC that supports a port speed of 1 Gbps or greater; 
unless explicitly stated, the speed of any GE port is 1 Gbps.

Содержание SmartEdge 100



































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды