Redback Networks SmartEdge 100 Скачать руководство пользователя страница 63

Страница: 63 / 98

Managing Hardware with CLI Commands

Determining Operating Status

5-11

Table 5-10 lists the fields that are displayed by the

show disk

command (in any mode).

Initialized

State of the card:

• No—Packet Processing ASICs (PPAs) have not been initialized.

• Yes—PPAs have been initialized.

Flags

Status of the card:

• A—Controller is active; always shown for slot 1.

• D—I/O carrier card has been assigned as the default traffic card; this assignment is

always reported against the first configured MIC in the system.

• E—Egress PPA is ready; reported for slot 2 only.

• H—I/O carrier card is administratively shut down; reported for slot 2 only.

• I—Ingress PPA is ready.; reported for slot 2 only.

• O—I/O carrier card is in the ODD state; reported for slot 2 only.

• R—I/O carrier card is ready; reported for slot 2 only.

Table 5-10

Field Descriptions for the show disk Command

Field

Description

Location

Location of the compact-flash (CF) card:

• internal—Card is installed in an internal slot.

• external—Card is installed in the external slot on the chassis front panel.

512-blocks

Size of the file system on this device in 512-byte blocks.

1, 2

1. The size of the root file system includes the sizes of the /flash file system and the p0 and p1 partitions on the internal-storage device.

2. The size of the /md file system does not include the partition for SmartEdge OS core dumps on the external-storage device; the partition

for core dumps is approximately 500 MB.

Used

Number of blocks in use.

Avail

Number of blocks available.

Capacity

Percent of blocks used in the file system on this device, calculated using the number of usable blocks
(Used + Avail).

3, 4

3. The number of usable 512-byte blocks (the sum of the Used and Avail fields) on a storage device is approximately 95% of the number

of 512-byte blocks.

4. The capacity of an external-storage device can decrease slightly over time if sectors are marked as unusable (cannot be read or

written).

Mounted on

Node on the file system tree onto which the device is mounted:

• / node.

• /md node.

Table 5-9

Output Fields for the show chassis Command (continued)

Field

Description

Содержание SmartEdge 100



































































































Результаты поиска

Содержание SmartEdge 100

Отзывы:

Бренды по названию

Популярные бренды

Redback Networks SmartEdge 100, Руководство по оборудованию

Результаты поиска

Содержание SmartEdge 100

Отзывы:

Бренды по названию

Популярные бренды