manualshive.com logo in svg

Redback Networks SmartEdge 100, Руководство по оборудованию

Поделиться
Скачать
Redback Networks SmartEdge 100 Скачать руководство пользователя страница 81

Adding and Replacing a MIC

Servicing the Hardware

6-9

3. Install the MIC; see the generic procedure in the “Insert a MIC” section on page 6-2.

4. If the MIC requires transceivers, install the transceivers, using the procedure in the “Insert a 

Transceiver” section:

5. After the transceivers have been installed, verify the operational status as described in the “Determine 

the Status of Native, Optical FE, Optical GE, and Copper GE MIC Ports” section on page 5-6 in 
Chapter 5, “Determining Operating Status.”

6. If you have installed transceivers, remove the dust cover from the connectors.

7. Connect and route the cables using the procedures in the “Connecting and Routing the Cables” section 

in Chapter 4, “Installing the Hardware.”

Replace a MIC

To remove an existing MIC and replace it with a new MIC, perform the following steps:

1. Ensure that you have the CLI prompt on the console.

2. Prepare for replacement:

a. Put on an antistatic wrist strap (one is shipped with the system), and attach it to an appropriate 

grounded surface.

b. Label and disconnect any cables from the front of the MIC being removed.

c. If the MIC has transceivers installed, install a dust cover over each SFP connector.

Laser

Risk of severe damage to your eyes. All versions of the optical SFPs are Class 1 devices, which 
use lasers to convert electrical signals to optical signals that can damage your eyes. To reduce the 
risk when working with optical SFPs, keep the connectors covered until you are ready to connect 
the fiber-optic cables. When you remove a cover, do not stare into or directly view the laser beam 
emerging from the connector.

Caution

Risk of data loss. You can corrupt the system if you attempt to install SFP transceivers that are 
not purchased from Redback, because these items have not been tested with the SmartEdge 
router. To reduce the risk, install only the transceivers purchased from Redback.

Caution

Risk of damage to fiber-optic cables. Fiber-optic cables are fragile and are easily damaged when 
bent. To reduce the risk, never step on a cable; never twist it when connecting it to or 
disconnecting it from an traffic card.

Caution

Risk of damage to fiber-optic cables. Fiber-optic cables are fragile and are easily damaged when 
bent. To reduce the risk, never step on a cable; never twist it when connecting it to or 
disconnecting it from an traffic card.

Note

Do not attach the wrist strap to a painted surface; there is an ESD convenience jack located on 
the front panel of the chassis.

Содержание SmartEdge 100



































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды