manualshive.com logo in svg

Redback Networks SmartEdge 100, Руководство по оборудованию

Поделиться
Скачать
Redback Networks SmartEdge 100 Скачать руководство пользователя страница 17

System Components

System Description

1-3

Controller Card Functions and Components

The controller card aspect of the circuit board manages the system; it is responsible for the packet routing 
protocols, the SmartEdge OS command-line interface (CLI), and

 

communications with a network 

management system running the NetOp™ Element Manager System (EMS) software. The controller also 
loads all configuration information necessary for the I/O carrier card and its ports.

Table 1-1 compares the controller card aspect of the SmartEdge 100 circuit board with the Cross-Connect 
Route Processor Version 3 (XCRP3) Controller card in a SmartEdge 400 or SmartEdge 800 chassis. 

The circuit board has these functions and components:

•

Dual processors that share memory and perform the controller functions

•

Memory—1 GB of synchronous dynamic RAM (SDRAM), which runs the SmartEdge OS and 
provides for shared databases that are accessed by the I/O carrier card and its MICs.

•

Nonvolatile RAM (NVRAM) with battery

The circuit board includes 512 KB of NVRAM, which stores the current state of the system; because it 
is not affected by power failures or system shutdown, the system can restore operations when power is 
restored or the system is restarted. 

Table 1-1

 Circuit Board and XCRP3 Controller Card Comparison

Feature

Circuit Board

XCRP3

Main memory (total)

1 GB

768 MB or 1 GB

NVRAM

Yes

Yes

Real-time clock

Yes

Yes

External timing implementation

None

Software selectable

System image and file storage

• Internal-storage device

• External-storage device

512 MB

1 GB

512 MB

1 GB

Ethernet management port

10/100/1000

10/100

Local console

Direct or terminal server 
connection only

Direct, terminal server, or 
modem connection

Note

A second internal-storage device is also installed on the circuit board and the XCRP3 Controller 
card for low-level software.

Note

The capacity of the internal and external compact-flash (CF) cards can vary on the circuit board and 
XCRP3, but the CF cards need not have the same capacity.

Note

Support for NVRAM is dependent on the release of the SmartEdge OS.

Содержание SmartEdge 100



































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды