manualshive.com logo in svg

Redback Networks SmartEdge 100, Руководство по оборудованию

Поделиться
Скачать
Redback Networks SmartEdge 100 Скачать руководство пользователя страница 73

Servicing the Hardware

6-1

C h a p t e r   6

Servicing the Hardware

This chapter describes servicing procedures for the SmartEdge

®

100 router, including servicing media 

interface cards (MICs) and transceivers, inserting and removing compact-flash (CF) cards, and how to 
obtain assistance.

Procedures in this chapter include:

•

Inserting and Extracting a MIC

•

Inserting and Extracting a Transceiver

•

Removing and Installing a CF Card

•

Adding and Replacing a MIC

•

Replacing a Transceiver

•

Replacing a SmartEdge 100 Chassis

•

Cleaning Optical Connectors

Inserting and Extracting a MIC

Caution

Risk of equipment damage. Electrostatic discharge (ESD) can damage SmartEdge router 
components. To reduce the risk, never attempt to remove or install a MIC, transceiver, or CF 
card without using appropriate ESD protection.

Note

The only tool needed to perform the procedures in this chapter is a #1 Phillips screwdriver.

Note

The term, GE, applies to any GE native port or MIC that supports a port speed of 1 Gbps or greater; 
unless explicitly stated, the speed of any GE port is 1 Gbps.

Note

After you replace a MIC or change its physical configuration, you must enter SmartEdge OS 
commands from the command-line interface (CLI) to restore the MIC ports to normal operations.

Caution

Risk of equipment damage. You can damage your SmartEdge router if you install and use MICs 
that have been repaired in the field. To reduce the risk, never attempt to repair parts or MICs 
yourself; always replace any defective MIC with a MIC supplied by your local technical 
representative.

Содержание SmartEdge 100



































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды