manualshive.com logo in svg

Redback Networks SmartEdge 100, Руководство по оборудованию

Поделиться
Скачать
Redback Networks SmartEdge 100 Скачать руководство пользователя страница 3

VCCI Class A Statement 

European Community Mark

Safety Notices

1.

Laser Equipment: 

CAUTION!

 Use of controls or adjustments of performance or procedures other than those specified herein may result in hazardous radiation exposure.

Class 1 Laser Product

—Product is certified by the manufacturer to comply with DHHS Rule 21 Subchapter J. 

CAUTION! 

Invisible laser radiation when an optical interface is open. 

2.

Lithium Battery Warnings: 

It is recommended that, when required, Redback replace the lithium battery.

WARNING! 

Do not mutilate, puncture, or dispose of batteries in fire. The batteries can burst or explode, releasing hazardous chemicals. Discard used batteries according to the 

manufacturer’s instructions and in accordance with your local regulations. 

Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type as recommended by the manufacturer’s instructions. 

VARNING

 Eksplosionsfara vid felaktigt batteribyte. Använd samma batterityp eller en ekvivalent typ som rekommenderas av apparattillverkaren. Kassera använt batteri enligt 

fabrikantens instruktion. 

ADVARSEL!

 Lithiumbatteri—Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med batteri af samme fabrikat og type. Levér det brugte batteri tilbage 

tilleverandøren.

VARIOTUS

 Paristo voi räjähtää, jos se on virheellisesti asennettu. Vaihda paristo ainoastaan valmistajan suosittelemaan tyyppiin. Hävitä käytetty paristo valmistajan ohjeiden 

mikaisesti.

ADVARSEL

 Eksplosjonsfare ved feilaktig skifte av batteri. Benytt samme batteritype eller en tilsvarende type anbefait av apparatfabrikanten. Brukte batterier kasseres i henhold 

til fabrikantens instruksjoner. 

WAARSCHUWING!

 Bij dit produkt zijn batterijen geleverd. Wanneer deze leeg zijn, moet u ze niet weggooien maar inleveren als KCA.

The marking on this product signifies that it meets all relevant European Union directives.

Содержание SmartEdge 100



































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды