manualshive.com logo in svg

Redback Networks SmartEdge 100, Руководство по оборудованию

Поделиться
Скачать
Redback Networks SmartEdge 100 Скачать руководство пользователя страница 11

Conventions

About This Guide

xi

•

Chapter 4, “Installing the Hardware”

Describes how to install the SmartEdge 100 hardware, including the SmartEdge 100 chassis and its FE 
and GE MICs, how to mount the chassis, connect the power cables, complete the installation, and 
connect and route the cables.

•

Chapter 5, “Determining Operating Status”

Describes the SmartEdge 100 chassis equipment LEDs and port LEDs, including those for the Ethernet 
management port, the native ports, and the ports on the FE and GE MICs, that you use to determine the 
status of the system. It also describes how to power on and off the system, how to manage the hardware 
using command-line interface (CLI) commands, and how to troubleshoot hardware problems.

•

Chapter 6, “Servicing the Hardware”

Describes servicing procedures for the SmartEdge 100 router, including servicing MICs and 
transceivers, inserting and removing compact-flash (CF) cards, and how to obtain assistance.

•

Appendix A, “Cables and Pin Assignments”

Provides cable and connector specifications for all SmartEdge 100 FE, GE, and management access 
cables and connectors, including MIC and native port cables.

•

Appendix B, “Alarms and Probable Causes”

Provides tables of alarm conditions and probable causes for the SmartEdge 100 chassis and its 
components, including FE and GE MICs.

Conventions

The conventions used for notes, cautions, and warnings provide special information in this guide:

Note

Provides related information for the topic described in the previous paragraph.

Caution

Describes a general warning, caution, or risk that could cause loss of data or damage to the 
system or one of its components and how to reduce that risk.

Warning

Describes a risk to you, the installation or service engineer, such as electric shock, that could 
cause bodily harm and how to reduce that risk.

Laser

Describes a risk to you, the installation or service engineer, from lasers which could cause severe 
damage to your eyes and how to reduce that risk.

Содержание SmartEdge 100



































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды