Redback Networks SmartEdge 100 Скачать руководство пользователя страница 85 | Manualshive

Страница: 85 / 98

Redback Networks SmartEdge 100 Скачать руководство пользователя страница 85

Cables and Pin Assignments

A-1

A p p e n d i x A

Cables and Pin Assignments

This appendix provides cable and connector specifications for all SmartEdge

®

100 Fast Ethernet (FE),

Gigabit Ethernet (GE), and management access cables and connectors, including media interface card
(MIC) and native port cables.

•

Management Access Cables

•

FE and GE MIC and Native Port Cables

Management Access Cables

A management access cable connects a console terminal, management workstation, or modem to the
Ethernet management port or the Craft port on the circuit board. Table A-1 lists the cables for these ports.

Pin assignments for the following cables are provided:

•

Craft Console Cable

•

Ethernet Crossover Cable

•

Ethernet Straight Cable

Note

The term, GE, applies to any GE native port or MIC that supports a port speed of 1 Gbps or greater;
unless explicitly stated, the speed of any GE port is 1 Gbps.

Table A-1

Cable Specifications for Management Access Cables

Maximum Length

1

1. The maximum cable length for RS-232 cables is for any baud rate.

Name

Description

System Connectors

Cable Connector

Feet

Meters

Craft console cable

RS-232

DB-9 female

DB-9 male

35.0

10.7

Ethernet crossover cable

2-pair category 5 shielded
twisted-pair

RJ-45 female

RJ-45 male

328.1

100.0

Ethernet straight cable

2-pair category 5 shielded
twisted-pair

RJ-45 female

RJ-45 male

328.1

100.0

«
...
83
84
85
86
87
...
»

Содержание SmartEdge 100



































































































Отзывы:

Нет отзывов