manualshive.com logo in svg

Redback Networks SmartEdge 100, Руководство по оборудованию

Поделиться
Скачать
Redback Networks SmartEdge 100 Скачать руководство пользователя страница 36

Getting Started

4-2

SmartEdge 100 Router Hardware Guide

Table 4-1 lists the tools that you need to install the SmartEdge 100 hardware.

 

Safety and ESD Considerations

To ensure a safe and trouble-free installation, follow these recommendations:

•

Site and Installation Considerations

•

General Safety

•

Electrical Precautions

•

Reducing the Risk of ESD Damage

Site and Installation Considerations

To ensure a safe and trouble-free site and installation, follow these guidelines:

•

Maximum recommended operating temperature

The maximum recommended long-term operating temperature for the SmartEdge 100 system is 104°F 
(40°C). Determine a suitable operating environment based on this recommendation.

•

Elevated operating ambient temperature

If the chassis is installed in a closed or multiunit rack, the operating temperature of the rack environment 
can be greater than the ambient temperature of the room. Remember this condition when you install the 
chassis.

•

Reduced airflow

Install the SmartEdge 100 chassis in the rack so that the airflow required for the safe operation of the 
equipment is not compromised. Air inflow is at the front of the chassis; air outflow is at the rear of the 
chassis.

•

Mechanical loading

Ensure you do not create a potentially hazardous condition from uneven loading when you select the 
mounting position in the rack for the SmartEdge 100 chassis.

Table 4-1

Tools Needed for SmartEdge 100 Installation

Tool

Purpose

#1 Phillips screwdriver

Install MICs.

#2 Phillips screwdriver

Attach the mounting brackets and cable management brackets to the chassis.

#2 or #3 Phillips screwdriver

1

1. Depending on the screws that you use to install the chassis in a rack, a #3 Phillips screwdriver might be more appropriate than the 

#2 screwdriver.

Install the chassis in the rack.

3/32-inch slotted screwdriver

Install DC power cables.

Cable crimping tool

Secure barrel, open, or ring lugs to the chassis ground cable; must be compatible 
with FCI YA4C series of compression lugs (Y2MR or equivalent).

Содержание SmartEdge 100



































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды