Redback Networks SmartEdge 100 Скачать руководство пользователя страница 25

Страница: 25 / 98

Preparing for Installation

3-1

C h a p t e r 3

Preparing for Installation

This chapter describes planning for the hardware installation, including site and management access
requirements for the SmartEdge

100 router and its Fast Ethernet (FE) and Gigabit Ethernet (GE) media

interface cards (MICs).

Topics in this chapter include:

•

Planning the Site and Installation

•

Selecting the Type of Management Access

•

Gathering Cables and Tools

After you complete the tasks in this chapter, you are ready to install the system as described in Chapter 4,
“Installing the Hardware.”

Planning the Site and Installation

This section describes:

•

Select the Installation Site

— Agency Compliance Information

— Electrical Specifications

— Environmental Requirements

— Physical Specifications

•

Select the Rack

•

Warnings

Note

The term, GE, applies to any GE native port or MIC that supports a port speed of 1 Gbps or greater;
unless explicitly stated, the speed of any GE port is 1 Gbps.

Содержание SmartEdge 100



































































































Результаты поиска

Содержание SmartEdge 100

Отзывы:

Бренды по названию

Популярные бренды

Redback Networks SmartEdge 100, Руководство по оборудованию

Результаты поиска

Содержание SmartEdge 100

Отзывы:

Бренды по названию

Популярные бренды