manualshive.com logo in svg

Redback Networks SmartEdge 100, Руководство по оборудованию

Поделиться
Скачать
Redback Networks SmartEdge 100 Скачать руководство пользователя страница 80

Adding and Replacing a MIC

6-8

SmartEdge 100 Router Hardware Guide

Figure 6-5

Installing a CF Card

Adding and Replacing a MIC

You can install a MIC in either MIC slot, regardless of the type of MIC installed in the other MIC slot. To 
add or replace a MIC, perform the appropriate task as described in the following sections:

•

Add a MIC

•

Replace a MIC

Add a MIC

To add a MIC to an operational system, perform the following steps:

1. Prepare for installation:

a. Ensure that the system is fully operational (you have the CLI prompt on the console).

b. Follow the guidelines in the “Completing the Installation” section in Chapter 4, “Installing the 

Hardware,” to select the slot for the MIC.

c. Put on an antistatic wrist strap (one is shipped with the system), and attach it to an appropriate 

grounded surface.

2. Loosen the captive screws and remove the MIC slot cover that is installed in the slot for the new MIC.

Note

Do not attach the wrist strap to a painted surface; there is an ESD convenience jack located in 
the lower right corner of the air intake panel on the front of the chassis.

Содержание SmartEdge 100



































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды