Redback Networks SmartEdge 100 Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 98

Redback Networks SmartEdge 100 Скачать руководство пользователя страница 47

Completing the Installation

Installing the Hardware

4-13

Completing the Installation

The chassis is shipped with the MICs installed, but you might need to install the transceivers in the native
ports and ports on any installed FE and GE MICs and an optional compact-flash (CF) card in the external
slot in the chassis front panel. These tasks are described in the following sections:

•

Install the MICs

•

Install a CF Card

•

Install the Optical Transceivers

Install the MICs

MICs for the SmartEdge 100 router are installed in the chassis when it is shipped. If you need to install
them in different slots, see the “Inserting and Extracting a MIC” section in Chapter 6, “Servicing the
Hardware.”

Install a CF Card

There is an external slot on the chassis front panel in which you can install a Type I CF card. If a CF card
is shipped with the chassis, it is installed in the external slot and no installation procedure is needed. To
install a CF card, see the “Removing and Installing a CF Card” section in Chapter 6, “Servicing the
Hardware.”

Install the Optical Transceivers

Optical ports require a small form-factor pluggable (SFP) in each port. These ports include native ports
when configured as optical ports, ports on the optical GE MIC, and ports on the optical FE MIC.

Perform the following steps to install an optical transceiver of any type:

1. Put on an antistatic wrist strap (one is shipped with the system), and attach it to an appropriate grounded

surface.

2. Ensure that the SFP latching mechanism is closed.

Laser

Risk of severe damage to your eyes. All versions of the optical SFPs are Class 1 devices, which
use lasers to convert electrical signals to optical signals that can damage your eyes. To reduce the
risk when working with optical SFPs, keep the connectors covered until you are ready to connect
the fiber-optic cables. When you remove a cover, do not stare into or directly view the laser beam
emerging from the connector.

Caution

Risk of data loss. You can corrupt the system if you attempt to install SFP transceivers that are
not purchased from Redback

®

, because these items have not been tested with the SmartEdge

router. To reduce the risk, install only the transceivers purchased from Redback.

Note

Do not attach the wrist strap to a painted surface; there is an ESD convenience jack located in
the lower right corner of the air intake panel on the front of the chassis.

«
...
45
46
47
48
49
...
»

Содержание SmartEdge 100



































































































Отзывы:

Нет отзывов